Question about Pelco KBD9000 Keyboard

2 Answers

Power went out now my pelco kbd300 isnt working

The power went out and now my pelco KBD300 isn't working. There is a way to reset it I think I just dont remember how to do it.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

If no power, it must one resistor of power interface circuit burnt. you need to send it for repair.
if it can be powered up, just can't cotrol. you can try to press the key of F5(AUX OFF), and powered it and hold "AUX OFF" for more 3 seconds and release. this mothod is used for calibrate the joystick.

Posted on Aug 10, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Kbd300a does not select monitor just it shows 00 on the display

Posted on Sep 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset KBD300 pleco keyboard


To initialize the keyboard, wait five seconds after powering-up the CM6700, enter the number for the
monitor you are viewing (1-4), and press MON. The LED display shows the number entered.
NOTE: You must re-initialize whenever power is cycled.
Source: http://www.jmacsupply.com/v/vspfiles/files/PMFiles/Pelco/Instructions/KBD300A-InstallationManual.pdf

Jan 15, 2015 | Pelco Kbd300a Pushbutton Control Keypad W/...

Tip

Pelco PMC10A Monitor 10 INCH COLOR HIGH RESOLUTION


We bought 6 Pelco PMC10A Color Monitors and they are working 24 hours a day. Suddenly after the warranty was over, the screen went totally black on 3 of them. After searching a while for the cause, Pelco seems to have used the wrong capacitor on their board close to the fly-back. They used a catalytic capacitor G-LUXON 4.7uf 50v and they have all busted by just looking at it on the board. I replaced the defect capacitor with a 4.7mf/250V Metallized Polyester Film Capacitor for about $2 each. They are now fixed! Hope this will help someone that has the same problem as I did.
REF: http://cgi.ebay.com/4-7mf-250V-Metallizd-Polyester-Film-Capacitor_W0QQitemZ220150073474QQihZ012QQcategoryZ4662QQrdZ1QQssPageNameZWD1VQQcmdZViewItem

on Dec 03, 2007 | Pelco Pel Monitor 12" B/W

1 Answer

Spin out of control


Reset the power to the camera and test first.
If it worked before you may have a wiring fault... or if it is new or someone tampered with it, the baud rate settings or protocol setting might have changed.

Apr 03, 2012 | Pelco CONTROLLER MATRIX- PTZ CONTROL

1 Answer

I have a pelco pmcl319 19" lcd monitor. when i switched it on the power (LEDlit) stays blue but it has no display. hope you have a solution for this. thanks.


First thing I would recommend is to get a flash light and shine on the surface of the screen where the Pelco name normally appears when first turned on. Next press the power button and watch at the center of the display. If you see a gray image of the Pelco name then the ccfl backlighting is no longer functioning. I have been able to order replacement ccfl lamps and if need be inverters that drive those lamps. These part can be purchased from http://www.lcdparts.net/. Disassembly of the LCD display is required as well as some soldering.

Feb 17, 2011 | Pelco 300 SERIES 19 INCH FLAT PANEL LCD...

1 Answer

Power Reset


First disconnect the plug. Wait 5 min. Plug back in. Then press the menu button and while holding it, switch it on. This should do the trick for most models.

Cheers
TeaCii
LiveOnline to earn money if you have website
Guard to watch you CCTV for $1

Apr 06, 2010 | Pelco PMCL 400 Series Flat Panel, TFT...

1 Answer

I have a Pelco ES30CBW35. Rewire the 230V/115V switch and transfo


this manual should help
  1. [PDF] Pelco EH3500 Series Environmental Enclosure_service manual
go here and down load it you'll need adobe reader to view it but, you can get it for free. Best of lock Rich.

Oct 23, 2009 | Pelco ES3012 5MLZ30W Esprit High Res Black...

1 Answer

Is there a main power reset button. my tv just


tv's haven't used reset switches since the 70's if you have no power something inside must be blown, without knowing what model you have it could be 100 things. but i'm sure it isn;t a switch, they almost never go bad. people always think it's the power switch or the cord, because it's the only parts they know, they don't realize what goes on for your tv to turn on, it could be alot of failures. you need a repairman.

Sep 15, 2009 | Televison & Video

1 Answer

Pelco Spectra III PTZ camera wrong fuse?


It is replaceable, as long as no harm has come to the rest of the camera.

Mar 14, 2009 | Pelco SD53C22 Smw 0 Spectra III Se White...

Not finding what you are looking for?
Pelco KBD9000 Keyboard Logo

Related Topics:

2,391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pelco Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Pelco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...