Question about Nordic Track Nordictrack Incln Train X3 Interact Treadmill Drive Motor For Model

Open Question

NordicTrack X3 incline trainer will start but when speed is excelerated stops

Treadmill will start but when excelerated the belt stops. Took off the back to run calibration and immediately noticed a black wire dangling unplugged (has red 2 adaptor). I cannot see where this needs to be plugged in. In addition, on Calibration Level 5 I get an error that states "brake not responding".

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 40 Answers

SOURCE: Nordictrack motor will not run when start button is pushed.

Likely the cover of one of the motor brushes popped off. Unplug the machine before you pop it back in place, then try it again.

If that doesn't work, most likely it's the motor control board, or possibly the console, or finally just a loose connection behind the console.


But most likely, it's the motor brush cover. I've been seeing that alot with this model.

Posted on Nov 01, 2009

  • 103 Answers

SOURCE: I NEED THE NORDICTRACK 9600 INCLINE TRAINER TREADMILL SCHEMATIC

contact me @ swflafitnessrepair@yahoo.com I will send this to you.

Posted on Nov 13, 2009

ercupa190
  • 12223 Answers

SOURCE: Nordictrack COmmercial 1500 console buttons don't work

http://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnes

11_17_2011_8_43_24_pm.gifsincerely. Please keep me in touch.

Posted on Nov 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

NordicTrack x9i Terrible banging sound coming from belt roller in back


Try to lubricate the treadmill running belt.
If you wish to get some details; visit the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Treadmill walking belt lubrication

Jan 02, 2017 | Nordic Track Exercise & Fitness

1 Answer

My Golds Gym trainer 480 treadmill minimum speed is 3 miles at lowest setting and it will not slow down when pressing the down arrow


Gold's Gym Treadmill Product Support ' ManualsOnline.com

fitness.manualsonline.com/support/golds-gym/treadmill/
My goldsgym treadmill just goes up and down when t. Gold's Gym ... my treadmill walking belt will not turn. ... Golds gym trainer 480 start button stopped working.

Repair Your Own Treadmill With Mark Peterson - YouTube

? 1:16
https://www.youtube.com/watch?v=B997gX07hW4
May 6, 2008 - Uploaded by Mark Peterson
A certified Fitness Specialist by the cooper clinic in Dallas, and a personal trainer for the first 16 years of my fitness career. .... I purchased a used Golds Gym Treadmill model# GGTL396100 which I tested when buying ... The treadmill will fully incline thennot go down, I have tried to recalibrate the incline ..

Nov 26, 2015 | Exercise & Fitness

2 Answers

My Sole F63 was working fine. One day, after we unplugged the treadmill and plugged it back in, the treadmill went through a start up process. It elevated the desk for a couple of seconds and stopped and...


I would check the main wiring harness, from the motor board to the console. Check the connection where the main frame connects inside the right upright bar. Remove the triangle shaped plastic cover bolt and side it up the upright bar. You will see the harness. Pull it through the acess hole the check the connection.Make sure all connections are tight.inclines motors rarely fail. To get it down you can reverse the red and black wires from the incline motor to the motor controller. Then run the calibration, once it's down just pull the safety key. It could be the display board or MCB

Dec 02, 2014 | Sole Fitness F63 Treadmill

2 Answers

My treadmill runs for 9 secons and stops and shows E1


Ok. So the first thing to try is to calibrate the speed.
You do this by doing the following:
  • With the SAFETY KEY in place, hold the ELEVATION UP and SPEED DOWN buttons for five seconds. The console will beep twice, "ENG0" will appear in the Distance window, and a number will appear in the Elevation window.
  • Press SELECT until "ENG3" appears; this is for Auto-Calibration.
  • Press START to Auto-Calibrate.
  • The treadmill will calibrate minimum and maximum speed, and minimum and maximum elevation. When Auto-Calibration is complete, the treadmill will reset to User's start screen. This process takes three to five minutes.
Make sure there are no errors. . .and that the speed goes from super slow to super fast and then stops. . .. if it stays slow. . or stays fast. .or error code appears during calibration, there is a problem.
If after a good calibration sequence, if it still does the stopping and E-1 after 10 seconds. ., then you need to (Power off and disconnect treadmill). . .then unplug the speed sensor from the lower power board, blow into the connector on the wire, and add a little contact cleaner spray to the connector on the board.
Recap: If it actually runs. . .but stops after a few seconds. . but the calibration runs and passes fine. .. .more than likely it is a speed sensor misread or a faulty speed sensor.

Sep 30, 2014 | Triumph 400T Treadmill

1 Answer

How to recalibrate 8600 incline trainer


To initiate the calibration routine, hold down the SPEED +
button and the SPEED - button simultaneously for three seconds. During the calibration routine, the INCLINE
TRAINER will automatically rise to the highest incline level and then return to the lowest incline level.

P.S. This is listed in your user manual in the "Troubleshooting" section if you don't have a user manual then you can get a pdf copy of it here
http://www.ereplacementparts.com/images/nordictrack/CTK59020.pdf

Aug 31, 2014 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

Wires are off of the incline motor, dont know which goes where, can you help?


You may have to have Nordic Track straighten things out by providing a diagram

Sep 29, 2013 | Nordic Track NordicTrack Incline Trainer...

1 Answer

X9i incline trainer clicking


Step 1:

RUN the calibration software . and fix it. God bless you



he Steps for Newer Style Console Calibration
1.Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
2.Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
3.Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
4.If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
5.Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
6.Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
7.Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
8.Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
9.Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
10.Press ENTER. You should see "SS" or "55" in the console.
11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
12.Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
13.When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
14.Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
15.If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Step 2:

2_8_2013_11_22_03_am.jpg

Feb 07, 2013 | Nordic Track Incline Trainer X9i...

1 Answer

Incline works but belt wont move


see the video and lube deck belt+rollers bearings
God bless you

Feb 03, 2013 | Free Motion X3 Incline Trainer Treadmill

Not finding what you are looking for?
Nordic Track Nordictrack Incln Train X3 Interact Treadmill Drive Motor For Model Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Paul Sikkema
Paul Sikkema

Level 2 Expert

171 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...