Question about Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A, 9.6v 1000mAh NiMh Pk 2-Way Radio

1 Answer

I don't have a screen display on my TH-79A. The radio is usless in this condition. Has anyone else had this problem and what was your fix?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 146 Answers

You could have a defective screen or a defective LCD driver, either way you have to replace it.
I 've replaced LCD screens before they typically are the entire front half of the radio inside wise. Probably going to cost a few to do it.

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My TH79 only shows channel numbers, what is the fault???


You should be able to enter the menus and change the freq display mode away from "alpha".

Jun 19, 2010 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

TH-79A Blank screen. It works with "F-switch on" but then goes blank.


Happened to me too. It takes some disassembling!!!! Between the screen and the underlying circuit board is a rubber strip with conductive material throughout which provides ''ground' for the display. This rubber wears out over time, but the quick fix is to turn it a quarter after cleaning and treating the contact surface with 'contact spray'( sparsely!!).

Job requires steady hand and pincers.

May 28, 2009 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

My th-79a shows channel numbers only


RTFM Page 29

Press [BAND] + POWER ON to toggle Channel Display

Gerard - PE1OUD

Mar 04, 2009 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

Unlocking Kenwood TH-22AT


http://www.radiomods.co.nz/kenwood/kenwoodth22.html

Dec 20, 2008 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

TH-79A amateur radio


TH-79A Kenwood HT and with the power off, hold down the MR button and the PTT switch, and while holding both of these turn on the power. The HT will come up in the remote control mode with the display indication "RC" on one band and the normal display on the other band.
.
To get the HT out of the "RC" mode just repeat the MR+PTT+Poweron sequence

Oct 30, 2008 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

KENWOOD TH-22AT WITH LOW VOICE


Drill a hole in the front panel. The mic is behind the front panel. Be careful.

Aug 12, 2007 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

TH-22AT WITH LOW VOICE


REPLACE THE PTT SWITCH, AND ADJUST THE MODULATION TRIMMER.

Aug 12, 2007 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

2 Answers

Kenwood 79a dual band transiever


There are several reasons for this, but one can be the flex that joins the display with the circuitry, carefully check if this is not broken or in this process or dirt.

Jul 02, 2007 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

Not finding what you are looking for?
Two-Way Radios Logo

Related Topics:

424 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Two-Way Radios Experts

eradiostore
eradiostore

Level 3 Expert

1640 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Kenwood Two-Way Radio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...