Question about Fisher and Paykel Aquasmart wl80t65c

1 Answer

Fisher paykel aquasmart fault 49

Fault 49

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Fisher and P... Expert
  • 554 Answers

Fault code 49 is water valves, But the Aqua-Smart board is outputting the wrong code here, The Smart pump has blown the water valves fuse, A common thing in Aqua-Smart Machines.
The Smart pump has jammed with lint and caused over current to the board and taken out parts on the board that drive the pump.
Best to get a new/recondition board for your machine.

Posted on Dec 19, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 30 Answers

SOURCE: i have trouble with my fisher and paykel washing

49. Cold Valve or Cold Valve & Hot Valve Faulty.


Posted on Dec 02, 2009

Testimonial: "thank you so much. now i understand what fault 49 is all about. however, can you help me fix the problem?"

  • 713 Answers

SOURCE: I put a small Carpet piece in my Fisher and Paykel

could b faulty control module. when pump jams or seizes on these machines it usually causes a fault in control module.whenever i found a control module faulty i always checked the pump for cause of fault.

Posted on Apr 08, 2010

  • 10 Answers

SOURCE: fault 49 smartdrive

Hi have had this problem on phase 5 grey controller, on the controll board near where the valve hot and cold wires are connected you will see a small usually blue resistor value approx 5ohms this is probably open circuit replace it check your water valves before reconnecting I was fortunate enough to have plenty of spare valves so I just replaced both valves as I suspect a faulty one may have damaged resistor machine has been working fine for some time since

Posted on Jul 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault 49


The main board is displaying the wrong error
for the problem your machine has.
Fault 49 is water valves error.
The most common problem with AquaSmart is pump faulty
and damaged your motor control board,
Pump and motor control board need replacing.

Jul 31, 2014 | Fisher and Paykel Washing Machines

1 Answer

Error 27 Fisher and Paykel


27. (00011011) Fabric Softener Valve Fault
The Motor Control Module has measured a voltage from the valve diagnostic circuit that
indicates the fabric softener valve (with Yellow Clip) is faulty. The most likely cause is that
the valve harness has not been connected correctly or the valve is open circuit. See fault
code 49 for service procedure.

Dec 30, 2013 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

Need a service, fault 49 ???????


cold valve fault. check the water supply, check the valves. otherwise it's the motor controller. replace parts as necessary.

Aug 28, 2013 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

Fisher paykel aqua smart fault 49


Fault code 49 is water valves, But the Aqua-Smart board is outputting the wrong code here, The Smart pump has blown the water valves fuse, A common thing in Aqua-Smart Machines.
The Smart pump has jammed with lint and caused over current to the board and taken out parts on the board that drive the pump.
Best to get a new/recondition board for your machine.

Apr 20, 2013 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

Fisher & Paykel Aquasmart WL80T65C 5 years old with fault 245, then 49.


Error code 245 is pump stall.
If the 1.6amp glass fuse has blown, the five mosfets on right side have shorted out there legs & blown the fuse.
Also check the pump drive parts for shorted legs.
There are three resistor that burn out near the fuse.
I will up loaded some pictures later.

2_9_2013_9_26_34_am.jpg


2_9_2013_9_26_58_am.jpg

Feb 08, 2013 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

TO FIX CODE 49 AQUASMART WASHINGMACHINE FISHERNPAYKEL


Yes you are right the pump in AquaSmart machines blows the water valves fuse that give you fault code 49.

Mar 18, 2012 | Fisher and Paykel Washing Machines

1 Answer

I put a small Carpet piece in my Fisher and Paykel Aquasmart WL80T65CW top loading washing machine. It disintergrated and the machine stopped displaying "I need service Fault 49" I have removed and...


could b faulty control module. when pump jams or seizes on these machines it usually causes a fault in control module.whenever i found a control module faulty i always checked the pump for cause of fault.

Apr 06, 2010 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

Fisher@paykel aquasmart WL80T65CW1 fault code245 and code49


hi my fisher & paykel aquasmart has a message saying fault 49 what does this mean?

Sep 03, 2008 | Washing Machines

Not finding what you are looking for?
Fisher and Paykel Aquasmart wl80t65c Logo

553 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Owen Barnes

Level 3 Expert

867 Answers

marley mcelhinney

Level 3 Expert

490 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...