Question about Fisher and Paykel Aquasmart wl80t65c

1 Answer

Fisher paykel aqua smart fault 49

Fault 49

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Director Badge:

    Uploaded 100 video answers.

  • Fisher and P... Expert
  • 540 Answers

Fault code 49 is water valves, But the Aqua-Smart board is outputting the wrong code here, The Smart pump has blown the water valves fuse, A common thing in Aqua-Smart Machines.
The Smart pump has jammed with lint and caused over current to the board and taken out parts on the board that drive the pump.
Best to get a new/recondition board for your machine.

Posted on Dec 19, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 713 Answers

SOURCE: error code 49 on fisher and paykel 8kg aqua smart

Hi just read your posting.Error code 49 means the computer has measured a voltage from the valve diagnostic circuit that indicates the cold valve is faulty.Would you like help in confirming that the cold valve is faulty?You need an electrical test meter.Please reply and I can guide you thru the testing procedure.Looking forward to your reply.

Posted on May 16, 2011

  • 10 Answers

SOURCE: fault 49 smartdrive

Hi have had this problem on phase 5 grey controller, on the controll board near where the valve hot and cold wires are connected you will see a small usually blue resistor value approx 5ohms this is probably open circuit replace it check your water valves before reconnecting I was fortunate enough to have plenty of spare valves so I just replaced both valves as I suspect a faulty one may have damaged resistor machine has been working fine for some time since

Posted on Jul 11, 2010

richroth
  • 9472 Answers

SOURCE: fisher@paykel aqua smart washer shows fault code49.

Fault 49 on F&P agitator models is bad cold water valve or wires on it disconnected.

Posted on Apr 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault 49 pops up on the screen


If your washer is a Fisher Paykel Top-Load Washer Error Codes = 49 I found this online by typing "Washing Machine Fault 49" into a google search engine...

Error Fault Condition - Water Inlet Valve Fault.
Repair or Check - Unplug the washer from power. Reconnect any non secure wires on the water inlet valve. Replace the wire harness if it is found to be damaged. If the wiring is okay then measure the resistance of the water inlet valves using an ohm meter. If the resistance of each water inlet valve solenoid is not 60 to 62 ohms then replace the complete water inlet valve assembly.
Parts for Replacement - Water Inlet Valve Assembly or Wire Harness.

Mar 09, 2016 | Washing Machines

1 Answer

What is the fault when the air bag dash light flashes code 49


It's a common fault on many Fords, usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat. Just push it together properly and it should clear the fault. If not, go under the drivers seat and secure all the wires and clips there as well.

Aug 21, 2014 | 2006 Ford Territory 4.0

1 Answer

Fault 49


The main board is displaying the wrong error
for the problem your machine has.
Fault 49 is water valves error.
The most common problem with AquaSmart is pump faulty
and damaged your motor control board,
Pump and motor control board need replacing.

Jul 31, 2014 | Fisher and Paykel Washing Machines

1 Answer

Fault code 49


Fault code 49 is a valve fault, but I have found it to often be the motor controller board at fault.

Oct 19, 2013 | Fisher and Paykel Washing Machines

1 Answer

Error code 49 f&p aqua smart wl80t65c


49 is a cold water valve fault. test the valve for voltage while filling, it should be recieving 24V. if not, the problem lies with the motor controller.

Aug 30, 2013 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

Fisher paykel aquasmart fault 49


Fault code 49 is water valves, But the Aqua-Smart board is outputting the wrong code here, The Smart pump has blown the water valves fuse, A common thing in Aqua-Smart Machines.
The Smart pump has jammed with lint and caused over current to the board and taken out parts on the board that drive the pump.
Best to get a new/recondition board for your machine.

Apr 20, 2013 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

Fisher and paykel toploader washing machine fault 49 water valves all show 60 ohms next step?


Fault code 49 is water valves, But the Aqua-Smart board is outputting the wrong code here, The Smart pump has blown the water valves fuse on it's overload, A common thing in Aqua-Smart Machines i always keep seeing,
The Smart pump has jammed with lint and caused over current to the board and taken out parts on the board that drive the pump.
Best to get a new/recondition board for your machine.

Nov 26, 2012 | Fisher and Paykel Washing Machines

1 Answer

Fisher@paykel aqua smart washer shows fault code49.


Fault 49 on F&P agitator models is bad cold water valve or wires on it disconnected.

Apr 25, 2012 | Fisher and Paykel Washing Machines

1 Answer

Cold&hot water valve dont seem to unscrew or do you have to buy the whole part


Fault 49 would most possibly be faulty motor controller board.
Not the water valves at all.

Mar 22, 2012 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Hi my washing machine saying fault 49 on it model WL80T65C


prob the capacitor faulty on motor , or start up windings on motor burnt out ,

Mar 22, 2012 | Washing Machines

Not finding what you are looking for?
Fisher and Paykel Aquasmart wl80t65c Logo

482 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Owen Barnes

Level 3 Expert

867 Answers

marley mcelhinney

Level 3 Expert

490 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...