Question about Canon Cameras

1 Answer

I have lost the power cable for my cannon legria21e

We have lost the power cable and need to replace it .How much can we expect to pay for a new one ?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 39 Answers

Approximately $20

Posted on Apr 20, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

When i power on my cannon 4412 printer it provide e202-0002 message

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies: ( 1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor.
(2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor.
(3) Replace the Contact Sensor.
(4) Replace the Main Controller Board.

Apr 04, 2015 | Cannon Office Equipment & Supplies

1 Answer


IT would be advisable to fix it exactly where it's broken, that is, for best results.

If you mean, where do you take it to?, then you'd need to look up the make/model of your unit and call the manufacturer for a Return Authorization. If it's under warranty, it should be repaired free of charge. If not, then expect to pay nearly what a replacement cable would cost.

Nov 10, 2013 | Audio Players & Recorders

1 Answer

Repairs to Cannon selphy cp710

Canon Selphy is a very low cost consumer product. If it is not under warranty (for new replacement), you can expect no support for it even here in the U.S.

Feb 08, 2013 | Canon SELPHY CP710 Thermal Photo Printer

3 Answers

2003 trailblazer shift cable broke loose, now tranny is in nuetral but shifter is stuck in park position, thus i now am unable place end of shift cable back on because it dosent line up! please help!

Ok, here is what you do, slide under vehicle, locate shift lever on side of transmission rotate counter-clockwise two clicks, pop shifter on, hop back inside turn key on depress brake pedal and check shifter, if it falls off again replace cable assembly they do not sell individual bushings, and get cable from dealer.

May 13, 2011 | 2003 Chevrolet TrailBlazer

1 Answer

1998 olds intrigue drivers door power windows cable broke i need to know how to recable it for it to work

this is a common problem on late 90s GMs. what you need is a new regulator. buy one on ebay and pay a glass shop to install it. Ten years is about all you can expect out of the motor so just go ahead and do the whole thing. labor to swap the regulator is much cheaper than to try and fix the regulator.

Oct 24, 2010 | 1998 Oldsmobile Intrigue

1 Answer

How much do I expect to pay for new brakes

It will vary on the brakes, depending what needs to be replaced, rotors, calipers, pads. I would say around $200-$300 per axle. I've seen tranmission services going for $79-$99.

May 29, 2010 | 2003 Volkswagen Passat

1 Answer

My ford ka power steering pipes have rotted away, ...

How much will you pay ? ............ " An arm and a leg " !! I had this same problem, Ford wanted

May 20, 2010 | Cars & Trucks

2 Answers

Need soft ware for my all in one mp210 cannon printer

Heres the driver and manual download page. First select your operating system then download your drivers. Hope this work for ya

May 12, 2009 | Office Equipment & Supplies

3 Answers


okay... go to your manufacturer's site and look for a download link for your drivers.. that's really all you need to do unless you are unsure of the manufacturer.. i can help again if you need to have me look for it online but will need model info on printer..
thanks and good luck, d

Feb 29, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
Cameras Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Cameras Experts


Level 2 Expert

176 Answers

old marine
old marine

Level 3 Expert

2104 Answers


Level 2 Expert

254 Answers

Are you a Canon Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides