Question about Amana NAV5800A Top Load Washer

1 Answer

Won't drain or spin

I have a top loader amana washer that won't rinse or spin..it washes the cloths but then stops when it is at the rise cycle .the tub is full of water...?

Posted by on

  • sfmedic Mar 12, 2009

    Thank you...I was thinking that or the timer..do u think it could be the timer as well...??

  • Anonymous Mar 18, 2009

    amana washing machine fills with water and will not agitate or spin. Washer is full of water. Amana model LWA65AW

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Sounds like the lid switch which is only about 30.00 to fix if you do it yourself. It's a little difficult but it's much better than replacing or having someone come in and do it

Posted on Mar 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Washing Machines will not rinse or spin


If the water won't drain out of your washing machine, either something is stuck in the drain hose or pump, or the pump is broken. Both fixes are simple if you're even just a little bit handy with tools. We're showing the repair on a Maytag washing machine.
What is wrong with a washer that does not spin?
If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. (Note: Direct-drivewashing machines do not have belts.) To diagnose the problem, do the following: 1Check the washing machine's spin cycle.
How to Drain Washing Machine That Won Drain Family Handyman
Washer Doesnt Agitate or Spin
Error codes in front load washers
Washing Machine Not Rinsing How To Fix
My washing machine stops at Rinse Does not DRAIN or SPIN
What causes a washing machine not to drain and spin?
If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Remove the hoses from the pump in order to remove the article of clothing.
SOLVED Why won my washer spin or drain Kenmore 110 Series Washing Machine
Maytag Washing Machines will not rinse or spin Google Search

on Dec 12, 2017 | Washing Machines

Tip

We have a Kenmore 90 series hvy duty top loader, it works fine in wash cycle but...


This advice is for all Whirlpool manufactured TOP LOADING washing machines. This includes Kenmore, Estate and Roper models as well. This is an easy repair that anyone with a little know-how and determination can perform.

First of all, unplug your washer. You will need to remove the console in order to get to the lid switch. The washer may have release tabs under the console at each front corner. Simply slide a putty knife straight in from the front at each corner and push in while lifting up. You should feel the release tabs push in and the console will pop up.

If not equipped with this type of console, you may have a console that has removable end caps. They can be removed by gently prying up on the top of them from the rear on each side. You may have to use a small screwdriver for this. The caps should pop right off. Once removed, you will need to loosen a screw under each cap. Once you have the console loosened, carefully lift it up and lay it back over the rear panel of the washer in its resting position. Be careful not to damage the small plastic hinges that hold it in place. Now you will need to perform the following steps:

1. Under the console you will find the white plastic lid switch connector plug. Unplug the switch from the connector.

2. There will be two brass colored clips. You will need to remove these to remove the machine casing. Place a flat blade screwdriver straight down into the opening on top of the washer and into the groove of the clip. Push the screwdriver away from you while holding into the groove and the clip will release.

3. Open the lid of the washer and place your hand under the front rim of the opening (DO NOT grab the wash tub). Now pull the case from the frame by lifting from the back first.

You do not have to remove it all the way from the frame, just enough to gain access to the switch. All there is to the switch is a couple of screws holding it in and a ground wire. It's a pretty easy repair job. Some models will have the switch located on the right-hand side of the lid rim opening, while other models will have the switch located adjacent to one of the lid hinges in the rear.

Once you've completed your switch installation, make sure you get the case back on the frame correctly by following these steps:

1. While looking down through the lid opening, place the front lip of the machine case UNDER the washer frame and start leaning it back onto the frame. There are four small cleats that must fit into four slots on the case or the washer will vibrate. Make sure the frame is seated properly, lean forward from the front of the washer, grasp both sides of the rear panel and pull towards the case. The rear panel should be seated and flush with the casing before inserting the retaining clips.

2. Insert the brass-colored clips into the slot on the washer rear panel first (this is the end of the clip with the 90 degree bend), and then push straight down into the opening on the top of the washer with some force. If you have the case seated correctly, the clips will snap back in.

3. Make sure you plug the connector from the console back into the lid switch receptacle BEFORE you reassemble the console. This is easy to forget.


I hope this information is helpful..

on Jul 26, 2010 | Washing Machines

1 Answer

Start matsui washing machine


Check the washer drain hose for clogs.

Jun 19, 2017 | Washing Machines

1 Answer

Clothes still wet after cycle is over


Be sure drain hose is not kinked and no higher than the top of washer to drain pipe. Remove clothes as soon as it stops spinning

Jun 23, 2010 | Kenmore 23822 Top Load Washer

1 Answer

Rise and spin


While the machine is operating take the timer knob and wiggle it around. If the machine cuts out momentarily then the timer is bad. If not then I would check out the lid switch to see if it is affecting the rinse and spin cycle.
Eric

Sep 17, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Washer won't drain or spin


top loader ??? or front loader??? if top loader you have broken your lid switch, will fill, agitate, but when it comes to drain/spin for safety reasons if the unit doent recognize the lid closed it will not advance...if yo have a front loader then i would suspect that something has gotten into the pump assy and preventing drainiing of water therefore will not spin

Mar 02, 2009 | Kenmore Washing Machines

1 Answer

Stopped mid wash cycle,no drain,no spin, will not go to next cycl


water pump blocked with nylon stuffing from old pillow.removed front panel from hinges under the lid. water pump at the right hand corner removed hose then removed 2 cups of nylon threads and stuffing forced into pumps small openings where it was compacted to a solid mass.

Jan 05, 2009 | GE Profile WPRE6100G Top Load Washer

1 Answer

NAV5800a top loader washer


The inside of your agitator became worn, and possible strip out the spline that allows the agitator to properly grip the shaft. The loud noise mustly occurs during the spin cycle. If you hear this loud noise your load of clothes may have become unbalanced. Stop the washer and redistribute the clothes, then re-start it.

Sep 02, 2008 | Amana NAV5800A Top Load Washer

1 Answer

Washer will not drain after wash cycle or the spin cycle


check to see if your pump is slightly plugged with a sock or ?

Your top loader should pump out in about a minute and a half when totally full of water.

Aug 11, 2008 | Whirlpool GSC9455 Top Load Washer

Not finding what you are looking for?
Amana NAV5800A Top Load Washer Logo

437 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Charles T Nevin
Charles T Nevin

Level 3 Expert

4070 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you an Amana Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...