Question about Black & Decker Nailers

1 Answer

Nails jammed in stapler so I took it apart splitting the halves.

Bad mistake, I need a diagram that shows me how to re- assemble the staple gun.

Posted by on

  • Kevin Young
    Kevin Young Mar 12, 2009

    Thanks for your quick response I finally got a phone number for the maker and shipped it to them.

  • David Ford
    David Ford May 11, 2010

    what is the brand and model number and I will try to help

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 40 Answers

Without knowing the brand and model number, the best I can offer is this: Since your question is listed under "all Black and Decker nail guns", have you tried going to www.blackanddecker.com and searching for your tool, or contacting their support section on the website? Or try typing your make & model # into a search engine, pick a place that sells parts and ask them to fax or e-mail a copy of the diagram (I have done this before to get diagrams).

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Handle stuck in locked position


One of the screws - furthest away from where the staples exit - has a nut on it... Remove the nut, then - using pliers - back out the screw. When I did this, the spring returned, a bent staple fell out and once re-assembled I could use the stapler again (for a few turns). It seems like the stapler is VERY sensitive to bounce during the stapling, you must hold it very tight (and flat) to the material so that the staple doesn't jam inside the stapler. Lousy product.

Mar 16, 2013 | Powershot Tool Company PowerShot 5700KB...

1 Answer

Got a staple jammed can't get out . don't know to take it apart.


This can happen all the time... first remove the slide-in tensioner which pushes against the staples. Remove the single bolt with lock nut which is towards the rear of the stapler. Now you can pivot the staple rail down and out of the gun. Just remove any twisted staples from the rail. Now reassemble the rail by positioning the front of the rail to go into the small slots in the front of the stapler body and re-attach the bolt. You may now reload the staples and tensioner and continue working. Takes just a minute or 2.

Jun 25, 2010 | Arrow No.ETF50PBN Extra Heavy Duty...

1 Answer

I have a tr250 nobody can show the loading part for the stapler.i need parts (no tension on staples)no spring or part that push against staple need part number & price. thank you Doug


I suggest you visit your local hardware store (Ace/Westlake) or you can try EBay, I've found numerous parts at great prices on there and they will usually designate what they will work with. Hope this helps. In the future, remove the material from your gun while keeping it stored, as this will weaken your magazine feed spring.

Jun 18, 2009 | Stanley TR250 H Heavy Duty Heavy Duty...

1 Answer

How do the staples stay in place in my stanley 1/4" stapler? They slide back and forth and therefore aren't in place for the stapler to work?


There should be a pusher that is attached to a spring. If the spring broke, or the pusher is missing the staples will not stay in place.

If you can locate a model number on the tool, you go to bostitch.com to find the parts you may need

Apr 18, 2009 | Stanley Tools Staple/Brad Nail Gun

4 Answers

My arrow fastener model t-50m is jammed how do I remove the few


I have a similar issue with my T50m stapler. To remove the staples unscrew the locking nut near where you load the staples and remove the tapppered bolt. The track will lift out and the staples can be easily removed. Why this is happening is unknown to me also. I purchased a new gun.

Feb 14, 2009 | Arrow Fastener 509 9/16" T50 Staples

2 Answers

Inserting brads into my Stanley TR250 Staple Gun


I bought one of these guns today and I had the same problem and it took me about 2 hours to figure it out as the instructions were very poor. Here how to load the brad nails:-

(a) Pull the slider bar all the way out
(b) Place the brad nail stick on the left side, IN FRONT OF the slider, NOT in the narrow gap in front of the two arrows where it says "LOAD BRADS"
(c) The nail heads should be facing the handle of the gun
(d) Close the slider and lock it
(e) Try it out. I tried nailing hardboard onto chipboard. The lever at low power only put the nail in about 30%. On Hi power it went in about 80%.

Good Luck
Peter

Jan 07, 2009 | Stanley TR250 H Heavy Duty Heavy Duty...

1 Answer

Need a diagram to re-assemble a stanly heavy duty sharpshooter.


If you have the exact model number you can call Stanley Bostitch directly. The schematic is no longer on line but customer service may be able to fax or email it to you.

The customer service phone number is:

1-800-556-6696
Hours: 8am-6pm EST (M-F)

Jan 04, 2009 | Stanley TR250 H Heavy Duty Heavy Duty...

1 Answer

Tr250 does not drive brad nails all the way down.


Jason,

I think this is typical of these staplers/nailers. I bought a lighter model Stanley the first time and had this problem. I took it back and exchanged it for the heaviest Stanley they had at Home Depot and had the same effect. It drove the stapler a little deeper but not all the way.

I did find that if I put all the down pressure on the stapler right on the edge where the staple comes out and then pull the trigger it would drive the staple almost all the way in. I think that there is a recoil effect (like with a gun) when you pull the trigger and the staple enters the wood. Try this. it will help.


Hope this helps Good Luck Loringh PS Please leave a rating if appropriate Thanks for using FixYa

Nov 06, 2008 | Stanley TR250 H Heavy Duty Heavy Duty...

3 Answers

Stapler works intermittantly


If not the power source or cord, the next activation point would be the trigger. Does the stapler make any sort of noise when the trigger is depressed? What type and model stapler is it?

Nov 02, 2008 | Arrow No.ETF50PBN Extra Heavy Duty...

Not finding what you are looking for?
Nailers Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Nailers Experts

John Trevino

Level 3 Expert

1378 Answers

yoopertech

Level 2 Expert

121 Answers

james allen
james allen

Level 2 Expert

109 Answers

Are you a Black & Decker Nailer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...