Question about Sony PS2 Dual Shock 2 Controller (PrePlayed) (PS2PRSODUSH2)

Open Question

My ps2 scph 70003 indicator turns green and goes back to red

My ps2 70003 indicator turns green and after 2 seconds it goes back to red light, when i insert a disk into my ps2 75004,it does not spin

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ps3 starts then turns off


try holding down the power button for 3 seconds

Apr 30, 2013 | Sony Playstation 3 120gb Video Game System...

1 Answer

How to setup online gamming


You need to have a wired connection. Plug one end of a ethernet (cat5/cat6) into one of your router's ports. Plug the other into the back of the PS2. You will have to sign up for a free Playstation Network account.

Oct 04, 2012 | Sony Playstation 2 Ps2 Slim System Console...

1 Answer

GT3-R -can


This is a dual frequency transmitter. (315/390) You need to select one button to program the TYPE 1 frequency of 390 MHz. Here's how:

Backwards compatable programming instructions for GT3-R dual-band remote: This is a 3 button remote, which can be used to operate up to 3 garage doors using IntelliCode radio controls. This remote is defaulted to operate the new IntelliCode 2 Genie garage door openers, but you can also program individual buttons to operate other IntelliCode 1 (pre 2011) models of Genie garage door openers made from 1998 to present. To change a button to operate a pre 2011 IntelliCode opener, the default IntelliCode 2 setting must be changed to IntelliCode 1. An LED light on the remote displays which mode the remote button is in: Red = IntelliCode 1 / Green = IntelliCode 2 To set one of the 3 buttons to be IntelliCode 1 (red), follow the instructions below:
  1. Select a button on the remote that has not been programmed.
  2. Press and hold that button for 10 seconds. Both Red and Green LEDs come on and stay on.
  3. Press the same button twice to toggle IntelliCode selection from IntelliCode 2 to IntelliCode 1.
  4. Press the same button again to confirm toggle. the LED should be Red. The IntelliCode selection for this button is set to IntelliCode 1.
You are now ready to program the remote to your garage door. Follow accompanying instructions for "Programming to IntelliCode 1 Genie garage door opener," or see below instructions: Programming Instructions: Gently press the Receiver Learn Code button on the power head receiver of your Genie garage door opener (motor head on ceiling in garage). This small, black, unmarked button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the motor head. When pressed, a radio signal indicator light will start blinking red for 30 seconds. After pressing the Learn Code Button, press your transmitter button twice for your system to grab the frequency and code it in. (Keep the transmitter you're tuning at least 2 feet away from the power head while tuning.) Press the transmitter button once more to test the system and start your door moving.

Jan 06, 2012 | PC Game Controllers

1 Answer

No of my ps2 cd is red in ps2 ?


Yes, the PS2 supports CDs, either red or white or blue.

Oct 31, 2009 | Sony PS2 Dual Shock 2 Controller...

1 Answer

My PS2 controller does the same.


its vibrating because it is probably grounded.. check for stuck buttons...try opening it and check the rubber underneath the keys

Sep 06, 2009 | Sony PS2 Dual Shock 2 Controller...

1 Answer

Ps2 dual shock black controllers are not recognized?


1.) i think u r controller pin is bend are broken

2.) or controller wire is cut

its better 2 buy a new controller

peace out >>>>>

Jul 26, 2009 | Sony PS2 Dual Shock 2 Controller...

1 Answer

My ps2 controller are not working the red light will not turn on when I insert the controller to ps2 unit


Sir your controller wire is damaged......in most of the cases its damaged from right behind the plug or controller it self.......all you have to do is to try changing the wire if you've got an old controller that don't work either change the wires of two.....use a screwdriver to takeout screws.....put the wires in the same manner as you took them out........it might work........you should also consider buying a new controller for your ps2 seriously........!

Jun 10, 2009 | Sony PS2 Dual Shock 2 Controller...

1 Answer

Ps2 dual shock2 controller buttons not working


Removed accumulated dust sticking on the board were the buttons touches.use cotton balls with alcohol or use clean damp cloth.If nothing's happen check the cord I'm sure it is twisted badly, open your ps2 use this controller and try to twist back the twisted cord if it stopped sometimes when your twisting it then you have to replaced the cord(make sure that your using the original ps2 controller not imitation)pls. rate

Jan 17, 2009 | Sony PS2 Dual Shock 2 Controller...

3 Answers

Ps2 controller buttons not working


what you can do is open the controller clean the board by using cotton buds with alcohol or cleaner you will notice accumulated dust preventing the buttons from touching the board you need to remove those.

Jan 15, 2009 | Sony PS2 Dual Shock 2 Controller...

1 Answer

UltraRacer playstation 2 controller programming


Here's the instructions on how to relocate buttons:

1. To assign one button (i.e. "R") to perform another buttom function (i.e.
"Z"): Press and hold the SET button for about 1 second to enter the
"FUNCTION SETUP MODE", the FUNCTION SETUP LED will illuminate and two beeps
will be heard.

2. Press the button (i.e. "R") you would like to reassign one time, the
FUNCTION SETUP LED will blink once and a single beep will be heard.

3. Press the new, desired function (i.e. "Z") one tim, the NORMAL LED
indicator will illuminate instead of the FUNCTION SETUP LED. Two beeps will
be heard. The setting process is now complete.

The UltraRacer will only return to its default setting when the buttons "A",
"L", and "R" are pressed at the same time BEFORE you turn on the console's
power. After about two seconds, the UltraRacer will generate three beeps to
acknowledge reset button configuration is set. To reset a particular button,
first press the SET button, then press the relocated button twice and then
press the SET button once more until the LED light goes off. THe button's
original function is used as a default button for further relocation.

These instructions were told to me bay a company selling these controls on AMAZON. I have been trying to reprogram mine and cant figure out where the "R" button is.

Nov 07, 2008 | Cables Unlimited InterAct UltraRacer Mini...

Not finding what you are looking for?
Sony PS2 Dual Shock 2 Controller (PrePlayed) (PS2PRSODUSH2) Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony PC Game Controllers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

steve morris
steve morris

Level 3 Expert

1673 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Sony PC Game Controller Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...