Question about Hotpoint 24 in. HDA3400G Built-in Dishwasher

1 Answer

HDA3400G020WW noise I have a Hotpoint dishwasher model HDA3400G02WW it makes a lot of noise, it makes loud click/bang at every cycle change, and loud humming

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 93 Answers

Dear sir the problem you have sounds like the solenoid that opens the drain actuater can be worn out open the bottom panel run tru a cycle observe when the solenoid open it may be that there is something causing the solenoid to buzz either worn out or a wire or something in the way causing not to close proprly thanks from gilles

Posted on Mar 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Indesit IDL40 dishwasher, loud bang with slight burning smell but still working?


Any burning smell is not good. Indicates that something in there is too hot and perhaps melting something. Could even catch fire......

Could very well be that whatever is responsible for the noise can be causing the problemo.

Sep 25, 2015 | Indesit Dishwashers

1 Answer

Loud sounds


Many Frigidaire dishwashers come with the promise of being the "quietest dishwasher in its class," according to Frigidaire. However, a quiet dishwasher doesn't necessarily mean that the dishwasher is silent, as some noises are normal. It can take some troubleshooting at times to determine if a noise coming from the dishwasher is typical or if it indicates a larger problem Listen for the sound of water filling and draining throughout the wash cycle. These sounds are normal and do not indicate an issue.

  • 2 Pay attention to the drain motor, which operates at the beginning of each cycle. This noise should be fairly quiet and should not sound like a loud, grinding or banging sound.
  • 3 Note that the sound will change when the wash cycle moves between the lower and middle spray arms. This sound should be temporary and fairly quiet.
  • 4 Look for hard items in the dishwasher grinder or filter if a loud crunching, buzzing or grinding sound is heard. The dishwasher can typically grind up these items within one or two cycles, but the item may be lifted out and discarded to eliminate the sound.
  • 5 Remove the bottom rack and spray arms from the bottom of the dishwasher if there is a loud noise coming from the dishwasher that does not resolve itself. Look inside for the impeller, which is round and spins. Remove any debris that may be clogging up the impeller or pump.
  • Oct 07, 2011 | Frigidaire Professional Series 24 in....

    1 Answer

    How old is my Hotpoint dishwasher, model HDA3400G02WW Serial SG8047194 is??? My dishwasher humms, but doesn't runs at ALL. What could be the problem????


    The motor is stuck. If you remove the lower cover and see a square aluminum motor it is less than 7 years old. Make sure power is off at breaker and rotate the motor shaft
    by turning the fins inside the motor.
    If the motor is black and round you have to turn
    the fan blade which is located in a slot between the metal pump and the plastic
    pump. Also once freed, a light shot of silicone or WD-40 (silicone works better) at the
    bearing ends. Also check pump for leaks around the drain solenoid (shiny shaft attached
    to a plastic triangle). If it's leaking during pumpout, the seal has failed. The pump runs
    around 100 dollars typically. Hope this helps.

    May 30, 2011 | Hotpoint 24 in. HDA3400G Built-in...

    4 Answers

    GE Dishwasher makes loud banging noise


    Check the stainless steel cover on the bottom of the lower rack sprayer. If it has been bent downward on either end, it will hit the inside panel of the door near the bottom. It may score the panel as it hits on each rotation of the sprayer.

    Just bend it back in position, carefully, with a pair of pliers. The technique required is similar to bending the pocket clip of a fountain pen back into the proper position after it has been sprung out too far. You might practice on a pen or mechanical pencil clip to see what I mean.

    Apr 06, 2009 | GE Dishwashers

    1 Answer

    Our new LG dishwasher makes loud clunking noise


    I believe this is a brand new dishwasher. Please listen carefully to determine of the sound you hear (clunk) is being made inside the dishwasher or is it being made near by. Most times, the problem is that the hot water pipe is baking the noise when the dishwasher closes the water inlet valve ... and the pipe goes "clunk"
    I have not had an LG dishwasher make a clunking sound inside itself when the cycle changes. Also, because this dishwasher is so very quiet (well insulated) the pipe banging would be louder than something inside the Dishwasher.
    If you have access to the hot water pipe, listen very near it when the cycle changes for the sound. Follow that pipe (hot water) pipe back and insulate it at the point it is banging. (or get a plumber to evaluate and resolve.)
    Please get back to me with what you find, OK?
    Good Luck!

    Apr 06, 2009 | LG LDF6920ST Stainless Steel 24 in....

    2 Answers

    Our dishwasher is making a loud noise during wash cycle.


    if you have a torx 20, and torx 15 screw driver, you an remove the screws from the top plate of the wash motor, and underthere youll see another t15 screw converingthe "chopper" assy, sounds as if a seed, of chicken bone, perhaps apiece of glass hasgottne down there

    Jan 25, 2009 | Whirlpool GU3600XTSY Stainless Steel...

    1 Answer

    Need owners manuel for Hotpoint Dishwasher Model HDA3400G02WW and repair manuel


    You can down load a pdf copy of the owner's manual from the GE website.

    May 12, 2008 | Dishwashers

    1 Answer

    Dishwasher Making Loud High Pitched Noise.


    How deep do you want to get into this?It sounds like the wash pump motor bearings that are worn.You can pull the unit out flip it over and wd40 the bearings in the motor or you can replace the bearings.Try to lube them first.

    Feb 23, 2008 | Dishwashers

    1 Answer

    Hotpoint Superplus 7822 dishwasher


    At the beginning of the cycle the dishwasher is attempting to pump out any residue water in the waste pipe and sump. It could be that the motor is sticking but you would probably also suffer from it not draining properly.
    It may just be noisy pump. I have a similar model and it is also quite noisy but nothing extraordinary.
    When the dishwasher is pumping out at the end of the washing cycle it may be quieter when there is water in the pump/pipes but then gets noisy as it 'pumps air'.

    Jan 29, 2008 | Hotpoint 23 in. BFI62 Built-in Dishwasher

    Not finding what you are looking for?
    Hotpoint 24 in. HDA3400G Built-in Dishwasher Logo

    565 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hotpoint Dishwashers Experts

    Mike Cairns
    Mike Cairns

    Level 3 Expert

    3053 Answers

    bosch5

    Level 2 Expert

    157 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17129 Answers

    Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...