Question about Craftsman 10" Table Saw

1 Answer

I have a Craftstman Table Saw Model #137.218240 and Serial # ROU 1041 and must replace the motor with a new one I have acquired. Where can I find a repair manual that will guide me in the proper replacement techniques?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

CLICK HERE for blowout diagrams that details part numbers and assembly.

There is no "repair guide" available for most small power equipment, as there are relatively few parts to assemble, and easily figured out.

Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FREE question.

Posted on Mar 10, 2009

  • sgprap67 Oct 17, 2010

    Ahelp that I have used in this digital age is to take one or more pictures of the unit before and as you are disassembly. It can help a lot in the assembly. Also use the exploded diagrams of the parts. Thirdly, have a friend that is mechanically savvy come over and do it over a brewsky as a favor. Sometimes two heads are better than one!!!

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a Craftsman 10" table saw Model 137.221960,


I have this saw. Motor just went on me (siezing up and smoking/burning) so if anyone can use parts then you're welcome to them. jmbombadil@yahoo.com in Conshohocken, PA.

Sep 20, 2011 | Craftsman 10" Table Saw

1 Answer

I need both pullys for the motor and the arbor. They are cast alu and need to be replaced.


call Sears,Have model and serial number ready,ask for parts and service,they sell any part for any craftsman power tool .

Jun 14, 2011 | Craftsman 10" Table Saw

1 Answer

Looking for cost of replacement motor for skilsaw model 3400 13amp for 10" table saw and where to buy from? Also, is there a 15amp replacement motor that would bolt right in to replace?


i looked online at places I get parts from. Neither listed the motor as a part the had the aramature for about $70 and the field for about $35. Have you tried the reset button? also it may just need new brushes.(if you see lots of sparks at the end of the motor opposite the blade, look through the air vent slots it is likely the brushes, unplug the saw, and take them out and replace them HERE is a blow up ) the I would think that if the saw is well used and the motor has burnt out. It may be a lost cause. I am not sure what the price of this was new but you can get a reconditioned saw from Amazon for 135 bucks. And it is a 15 amp saw.

Dec 07, 2010 | Skil 10" Table Saw 3400

1 Answer

Have a craftsman 10 inch table saw model #137.218250, serial #RCW3145. When we attempt to cut plywood or a 2X4 length ways, the motor dies a number of times. Most of the time the reset button will not...


sounds like the reset button needs replaced. Also when is the last time you cleaned the motor area?? When you reset the button is the motor "hot" to the touch and if so could also be a motor problem,, try the reset first

Aug 26, 2010 | Table Saws

1 Answer

TABLE SAW MODEL JTAS-10-1 SERIAL # 9031109


my table saw jet model jtas-10-1 serial # 9031109 stock # 708510

Aug 21, 2010 | Jet 10" Xacta Saw Left Tilting Arbor...

1 Answer

Fan and fan guard needed for 3 hp motor. Have serial number for motor on a 12 inch craftsman tablesaw.


I'm assuming your saw is a model 351.228040 or a 351.228020. Manual is here.
See page 18, Figure 7 for the Blade drive exploded diagram.
Sears doesn't appear to have a part number for the fan and fan guard.

It looks like you can replace the entire motor and key for $217.55 (as of 6/13/2010) which isn't too bad for a 3 HP motor. Part number is 15094.00 and clicking it will link you to their parts site.

If this answer was useful, please give it a thumbs up. Thanks!

Jun 07, 2010 | Craftsman 10" Table Saw

1 Answer

Want to replace under powered saw motor on sears 10"table saw


u can put a 2 and above if u want just need to have the correct rpms

Jan 26, 2010 | Craftsman 10" Table Saw

4 Answers

New or used motor for a Craftsman 10" table saw


Sears no longer sells repair parts for this motor, only the whole motor as a replacement part, and it is $140.00, but you can buy replacement bearings from drillspot.com the bearing needed is an Enduro 6200 zz c3

Apr 26, 2009 | Craftsman 10" Table Saw

1 Answer

New or used motor for a Craftsman 10" table saw


You can try Sears but they can be a bit pricey. I use to send out motors for a factory I worked in to a rebuilder who would even do new windings. Check in your area for a rebuilder, As for the replacement being a Sears unit they may have a similar motor in stock. Good luck.

Apr 16, 2009 | Craftsman 10" Table Saw

Not finding what you are looking for?
Craftsman 10" Table Saw Logo

Related Topics:

670 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Table Saws Experts

Mike

Level 3 Expert

4331 Answers

80stech

Level 2 Expert

92 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Are you a Craftsman Table Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...