Question about LG Studioworks 700S 17" CRT Monitor

1 Answer

My moniter wont boot its on standby mode

I just switched it on and it didnt startup

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

It is the cold solder problem.pls solder the board careefully

Posted on Mar 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Problem showing "out of range


You need to change the display resolution of the computer. for the purpose you change the video adapter settings as follows:


Restart the computer, and while it is restarting, press F8 until the Startup menu appears. Press 3, and then press ENTER to start the computer in Safe mode.

Right-click the desktop, click Properties, and then click Settings.

then you change the resolution to 1024x768

and restart computer in normal mode


hope it will work, feel free for further assistance


do rate the solution if got help

Dec 03, 2010 | Compaq FP 7317 17" LCD Monitor

1 Answer

Monitor stuck in standby


Try tapping F8 when booting and then choose 'safe mode with networking'
if this works go to the lcd manufactures web site and look for a specific driver for your screen.

Aug 30, 2009 | Dell E551 15" CRT Monitor

1 Answer

Intstalled starlogic moniter to PC and got error message


Hi,
the "Out of Range" message usually appears when the video card is putting out a video resolution or frequency that the monitor isn't able to handle. You should reboot your computer and BEFORE the Windows screen shows up, press the F8 button once every half-second. THis will bring up the boot menu for Windows. Select "Enable VGA Mode" and press enter. THis will load Windows in VGA mode where the screen resolution will be 800x600 @ 60Hz. Any modern monitor is able to use this. Once you log into Windows with the basic video settings, you can go into the Display properties within Windows and bump up your resolution and frequency as needed.

May 11, 2009 | Computers & Internet

1 Answer

Moniter wont work


Possible reasons for this is a defective video card or the monitor itself or Windows installation failure. First, isolate the problem by swapping a working monitor to your system and check if the problem still persists. If it still doesn't work, then video card is the culprit. Some defective video cards function only on the lower resolution settings, which is the default resolution in the installation process of Windows XP. When the installation is finished, boot loader set the user interface to a much higher resolution which the defective video card is incapable of.

To further verify this, try pressing F8 and start Windows XP in a Safe Mode. If it boots properly, then Windows XP is incapable of going across the normal mode.

Jul 18, 2008 | HP Pavilion MX70 17" CRT Monitor

1 Answer

Oversize Message


dear,

run the system on safte mode and then try to manage your screen resolution to minimum and then restart it normally..

regards,

dont forget to rate

Jun 20, 2008 | Kogi l7eh-ta ko 17" Flat Panel LCD Monitor

1 Answer

No Display.


the problem is seem to be in your moniter vedio driver ic which is present inside the moniter it is programmable ic, it may get heated or corrupted so pls check your moniter

the service manuals are available at eservice.com

Mar 18, 2008 | ViewSonic VA2012WB Monitor

1 Answer

Will not close down


These monitors go into a standby just incase you are only restarting the PC.
To turn it off properly, hit the power button on the monitor before Windows has completely turned the computer off.

IE: tell Windows to shutdown, when you see the blue screen telling you Windows is shutting down, turn it off then.

Hope that helps

Oct 20, 2007 | Acer AL1715 17" LCD Monitor

1 Answer

BLANK SCREEN


screen goes dark I tried the moniter in a different pc with the same result. i think there might be problem in monitor adjustment. 2 if it is ok then the problem in video section. 3 also check for loose connector 4 crt base might be loose.

Sep 26, 2007 | Dell E773C 17" CRT Monitor

1 Answer

Monitor problem


It sounds as if you have a resolution set that the display does not support. Restart your machine in safe/VGA mode by holding down F8 while the machine boots. Once in safe mode, set the resolution (Right click--> properties--> Settings--> Screen Resolution) to one that your display supports.

Jun 18, 2007 | Dell UltraSharp 1704FPT 17" Flat Panel LCD...

Not finding what you are looking for?
LG Studioworks 700S 17" CRT Monitor Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18333 Answers

Teet Bergmann

Level 3 Expert

565 Answers

Are you a LG Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...