Question about Linksys (NH1005) 5x10/100 Mbps Networking Hub

1 Answer

Switch compatibility problem.

I have 2 switches for my network.
1) Cisco Catalyst 500 series manageable switch
2) DLINK 1024D unmanaged switch.

Both are connected by RJ45 straight cable.

My broadband is connected to a port in the Dlink switch and in the catalyst switch I connected a modem for a leased line that connects my other remote sites.

The problem is:
The users connected to the Dlink switch does not get access to the broadband when they have the router's IP as the first default gateway and the broadband IP as the second gateway.

The broadband connectivity is through if I interchange the position, but then the remote sites are unreachable.

Is it because the two switches are incompatible? or am I doing some mistake?

Please help me out.

Posted by on

  • 1 more comment 
  • len_kamei Mar 12, 2009

    DLINK is just a switch, not a router. The broadband is connected to it.

    The leased line is connected to the Cisco Switch.



    Communication is possible since the users from the DLINK switch can get updates from the Antivirus server which is connected in the Cisco switch. Ping between users is also through.



    Keeping Router IP as gateway:: The problem is the router is for connecting only the remote locations, and is not for broadband. If i give the IP of router only as Gateway then the Broadband is not available.



    Do you suppose that I should have the broadband through the router?



    As of now, the ISP has provided a modem for the broadband which is connected to a port in the DLINK switch, this in turn is accessed by the users by putting in the Modem's IP as gateway along with the router's IP add.

  • lord_loki
    lord_loki May 11, 2010

    This sounds like a routing problem to me. Users should only have one gateway. This should be the IP address of the router. This is handled either manually or through your DHCP. Can you communicate from a user on the dlink to a user on the cisco?

  • Jim Brauer May 11, 2010

    Does the Cisco switch have routing capabilities? And if it does are you running a sub-net with the other switch (now the DLINK you said is just a switch, right, not a router). If the DLINK is just a switch, and your leased line is connected to that first, you got a problem with routing.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 50 Answers

I think you need to go from the leased line to the ROUTER first. The switch you said was unmanaged...so as far as I can tell there is NO IP for the DLINK. If that's the case your router needs to be before the switch and after the modem.

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The power devices that Cisco Catalyst 2960 Series Support?


The Cisco Catalyst 2960-48PST-L can support 48 PoE ports with total PoE power output capacity at 370W. Taking advantage of Cisco Catalyst Intelligent Power Management, the Cisco Catalyst 2960-48PST-L configuration can deliver the necessary power to support 24 ports at 15.4W, 48 ports at 7.7W, or any combination in between.

The Cisco Catalyst 2960-24PC-L can support 24 simultaneous full-powered PoE devices at 15.4W for maximum powered-device support.

The Cisco Catalyst 2960-24LT-L can support eight PoE devices at 15.4W
Cisco Catalyst 2960 Switches for the details

Aug 15, 2014 | Computers & Internet

1 Answer

Advise: Cisco Switch for small business?


I think Cisco Catalyst 2960 & 2960S Series Switches with LAN Lite, Catalyst 2960 Series Switches with LAN Base, and Catalyst 2960-S Series Switches with LAN Base is best choice. You can get more information in http://www.3anetwork.com/blog/cisco-switches-for-small-business/

Aug 04, 2014 | Computers & Internet

1 Answer

What's the difference between the Cisco 3850 and 3750-X series switches?


The difference between them as below, hope can help you to choose the best switches on your business.
1.Stacking bandwidth: 3750X for 64 Gbps while 3850 for 480 Gbps

2.Cisco IOS software wireless controller: 3750-X has none while Catalyst 3850 has

3.Queuse per port: 3750 has 4 while 3850 has 8

4.Quality-of-service model: 3750 with MLS while 3850 with MQC

5.Uplinks: 3750 be equipped with 4 x 1GE2 x 10GE NM4 x 1 GE or 2 x 10GE SM
3850 be equipped with 4 x 1GE2 x 1/10GE4 x 1/10GE(on 48 port model)

If you still have any question, you can log in
http://www.3anetwork.com/cisco-switches-price_c1
to know more about the datasheet and specification about the Cisco switches.

Jul 31, 2014 | Cisco Computers & Internet

1 Answer

How can we cascade two switches


cascade? or connect? easy connect the internet in 1 switch and from that 1 connect it to the bottom

Jul 25, 2014 | Cisco Small Business 100 Series Unmanaged...

2 Answers

Cisco Catalyst 2960-S VS 2960-X Series Switches?


2960-X is manual configurable and 2960-S is smart dont need to configure.

Apr 10, 2014 | Computers & Internet

1 Answer

How do I connect cable modem to cisco 3560 switch and configure it?


The cable modem will need to go through a router because it needs a NAT and PAT translation table, connecting the cable modem direct would lose the ability to get to the internet.

Jun 05, 2012 | Cisco Catalyst Compact 3560-C PD PSE -...

1 Answer

It is manageble or not


The 24-port D-Link DES-1024D is an unmanaged switch.

Mar 09, 2011 | D-Link DES 1024D (DES-1024D) 24x10/100...

1 Answer

HAVE 24 PORT CISCO CATALYST 2960 SERIES SI ,HOW TO PUT IT BACK TO FACTORY SETING SO I CAN USE ALL 24 PORTS WITHOUT MANAGE..???


Due to the length of the solution I have provided you with a link to the Cisco site on how to reset catalyst switches.

It is not a simple process and you need to read the instructions carefully.

http://www.cisco.com/en/US/products/hw/switches/ps607/products_tech_note09186a00800c4546.shtml

Dec 15, 2010 | Compaq Cisco Catalyst 296024S switch 24...

1 Answer

Need to locate PC's on our network, accurate to the switch port.


If its not to many computers , tone out the lines with a network toner

Jul 06, 2009 | Cisco Catalyst 3750G-24T SMI...

Not finding what you are looking for?
Linksys (NH1005) 5x10/100 Mbps Networking Hub Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2259 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18333 Answers

mark

Level 2 Expert

105 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...