Question about Ace Hardware Drills & Drill/Drivers

1 Answer

I want to down load my Acer Aspire 4920G home edition Driver. coz i want to change Window XP.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the product key for windows vista home premium. I didnt make the recover cd. Now i cannot boot.can i download the recover cd with this product key?

Posted on Apr 18, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My batteries are dead, can I connect the step down wall charger directly to the contacts for the battery inside the handle and use it like that?

This can be so frustrating. The power available from the charger is not enough to operate the drill motor at load. After going through several NiCad drills, chargers and batteries I ended up getting a Lithium battery drill that is so far about two years old staying healthy a lot longer.

I have rigged a 12 vdc version of a NICad drill to a lighter plug and used it in the car. Alligator clips ended up working better but the power loss in the wires defeated the real benefit.

Porter Cable makes a drill PCCK600LB (The part numbers are tricky the one listed is the one to buy) I had had a opportunity to work with the less powerful model PCC601 and was impressed. This model is the more powerful version and I'm super happy with it. It comes with two batteries that are high output, Orphan drills no case or batteries are available e-bay for pocket change. I purchased the low end version( PCC601) to go with this model using the second battery from the first drill. One for the drill and this one for the driver.
PORTER CABLE 20 Volt MAX Drill Driver

Hope this helps?

Jan 17, 2016 | Drills & Drill/Drivers

1 Answer

3/8" cordless driver can't change the

If debris enters the chuck it may no longer turn for adjustment. Spray plenty of wd40 into chuck and allow plenty of time for oil to do its magic. Hold chuck/drill pointing down and turn drill in both directions to clean out debris. If chuck is too far gone, remove the center screw (backwards thread) and remove the chuck(threaded on). Replace the chuck with new generic part from Lowes (about $25.).

Sep 20, 2011 | Dewalt Drills & Drill/Drivers

2 Answers

When I bought this item it stated that you could fix sockets onto the end of Impact Driver. I am unable to see how they fit onto the end of Driver. Is there an attachment made for this purpose? Thank You...

You have to distinguish between Driver and Wrench. Driver has 1/4'' hex hole where you can insert standard bits. Wrench has a 1/2 or 3/8 Square drive and you can put sockets directly on it. Wrenches have usually higher torque compared to drivers. DC827 is driver, you might want to change it for DC822, or you can use adaptor from 1/4 to 3/8 or 1/2 Juraj

Oct 20, 2010 | Dewalt 18v Nano Cordless Impact Driver...

1 Answer

How to change the drill head

If you man changing the chuck, take out any drill bits and look down into the chuck. You will see a screw holding it on. On many drills this screw has a reverse thread so it loosens in the opposite way to regular screws. You have to undo this screw to remove the chuck, then fit a new one of the same spec or one suitable for the drill and reassemble in reverse order.

Mar 31, 2010 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

1 Answer

Why does my drill run hot

Maybe ur drill is not heavy duty type.You need to rewind the motor,but if i were you buy a new one.YOu may use the old one but its good for few minutes after using it.

May 19, 2009 | Dewalt 18v 1/2" Compact Drill/driver Kit...

3 Answers

How do you change the drill bit for a Ryobi?

My husband explained this, via phone ..... made it simple....... grab the silver ring area beneath the black top area where the drill bit is located. Hold the silver area firmly, while you twist the black top. You will see the release, then remove drill bit. Laymen's terms, but it worked!!

Mar 16, 2009 | Ryobi 18v Variable Speed Impact Driver...

1 Answer

Load and adjust

I would go to and in the section under Factory and Authorized Service Centers click on that and there is a window to view and download manuals for this tool, just type in your model number. Dave

Dec 24, 2008 | Drills & Drill/Drivers

1 Answer

Puller Question

Six routines must be followed in order to minimize the chances of your hydraulic equipment suffering costly, premature component failures and unscheduled downtime: * Maintain fluid cleanliness; * Maintain fluid temperature and viscosity within optimum limits; * Maintain hydraulic system settings to manufacturers' specifications; * Schedule component change-outs before they fail; * Follow correct commissioning procedures; and * Conduct failure analysis.

Aug 27, 2008 | Black & Decker/DWLT DW2518 30-Piece Rapid...

1 Answer

Drill Motor Reliablity

some models have external brushes for easy changing - when the brushes wear down you can easily change them for new ones, some models have this feature ,it is only of use if you are using your cordless drill on a daily basis.

Aug 27, 2008 | Dewalt DW056 18 Volt Cordless Impact...

Not finding what you are looking for?
Drills & Drill/Drivers Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ace Hardware Drills & Drill/Drivers Experts


Level 3 Expert

60667 Answers


Level 3 Expert

479 Answers


Level 3 Expert

2384 Answers

Are you an Ace Hardware Drill and Drill/Driver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides