Question about Honda Chipper Blower and Vac: 5.5 Hp Gas

1 Answer

Ryobi RBL30MVA petrol blower problem

Hi, my (brand new) Ryobi RBL30MVA petrol blower is running but does not seem to be revving up very high.The enging note just does not seem to be hitting full rev's and the wind speed created does not seem powerful enough.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 36 Answers

If this is a brand new I would ask is the gas oil mixture fresh and of the proper ratio. most use 40-1
if this is not brand new look and see if the muffler could be clogged up. a common problem is the spark arrestor screen gets clogged up with carbon deposits.

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brand new Ryobi 2-cycle backpack leaf blower. It will not run full throttle. Should I take back and get new one or ?


Take it back. If the new one doesn't perform like it should get your money back and buy a Stihl. They will fuel and run the machine before you ever leave the dealer with it to make sure it runs like it should and they can answer any questions and even get you parts. Husqvarna may do the same thing

Nov 20, 2014 | Ryobi Leaf Blowers

1 Answer

Why is my petrol tank pressurised in my petrol blower?


There will always be some pressure in the tank, if the fuel in your area is poor quaility i have seen the fuel actually boil in the tank increasing the pressure and causing poor running.

Feb 23, 2013 | Ryobi Leaf Blowers

1 Answer

Ryobi 30cc trimmer won't run. Difficult to start, hard to keep ru


chnge the plug for the best you can get then depending on the mix petrol oil mix u could cahnge that ie if its 50:1 go down to 40:1 or visa versa if that doesnt work bin it and get a sthil or an ehco

Jun 23, 2010 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

2 Answers

Ryobi CS30 - Stalls out?


Dirt or varnish in fuel filter or carburator. Change filter if there is one.

Flush out the carb with a varnish remover.

Open high speed needle valve 1/8 turn farther, then turn in while running until it just smooths out.

Jun 07, 2010 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

2 Answers

My Ryobi RBL30MVA. leaf blower will not start, when pulling stater chord it feel as if it is not engaged with engine ie engine does not turn over


I have had this exact same problem with the same model after just one hours use.

Returned it a week later and after 2 months the replacement did the same thing.

Returned that one and got a third. A week later that ones doing the same thing again after only an hour or so use.

Obviously some defect in them.

I'll be getting my money back and visiting the local mower center to get their help rather than doing the guess work my self and ending up with a dodgy model

Nov 07, 2009 | Ryobi Leaf Blowers

1 Answer

RYOBI RBL-30MVA 30cc when pressing the primer bulb to allow petrol thro, nothing happens? and as its not letting the petrol thro, the leaf blower will not start....any suggestions? thanks ben.


The diaphragm in the carb may need to be replaced. Make sure all your fuel lines are fine. On these inexpensive blowers the fuel lines tend to get brittle and crack and fall apart.

Oct 08, 2009 | Ryobi Leaf Blowers

1 Answer

The engine revs high then low.


There is a way to remove fuel filter although I don't know if you can clean you might have to replace it. Other reasons for high and low revving could be that the carb might be adjusted correctly.

Aug 08, 2009 | McCulloch Trimmer Plus Attachment: Add On...

1 Answer

RLT30HT 30CC PETROL STRIMMER difficult to start


Hi,
The plug that I have in my 720r is a Champion RDJ7Y. Can I suggest that you pull the old plug out and look to see which one you have? Also when you buy the new replacement it should already be gapped for what you need.
Good luck!

Jul 27, 2009 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

1 Answer

My new Ryobi boggs down/ stalls as soon as I pull on the trigger.


You should have 2 small adjuster screws next to each other on top of the carb.Try adjusting each of them a little with a thin screwdriver as the engine is running.Put strimmer on the ground first and adjust screws while you are revving engine until it runs correctly.Trial and error and very small adjustments can make quite a difference.Hope this helps.

Jun 12, 2009 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

2 Answers

Ryobi PBV-30A Carb problem


I have a rayobi PBV30A petrol trimmer and it keeps dying once you increase the throttle speed runs on idle.

Feb 17, 2009 | Ryobi Leaf Blowers

Not finding what you are looking for?
Honda Chipper Blower and Vac: 5.5 Hp Gas Logo

931 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Leaf Blowers Experts

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

375 Answers

Wade Mobley
Wade Mobley

Level 2 Expert

448 Answers

Are you a Honda Leaf Blower Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...