Question about Lexmark X642e All-In-One Laser Printer

1 Answer

Lexmak x642e My dsl went down and when it came back up my employees could no longer print. What should I do?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Have you powercycled the printer? Is the printer showing ready, currently?

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I installed a maintenance kit (fuser, charge roller, transfer roller & pickup rollers) in my Lexmark x642e and I'm still getting light horizontal lines approx. every inch or so thru the page


Have you tried a different cartridge? Was there much spilled toner inside the printer? If you go into menus, and then help menu you can print a print defect guide that you can line up on your print and it will tell you exactly which part is causing the issue.

Mar 06, 2011 | Lexmark X642e All-In-One Laser Printer

1 Answer

Hello, I got an Lexmark X642e with 900.80 error (when the ADF scanner is connected). When scanner is not connected, the printer is accessible via network and can print w/o any problem. Firmware is...


A 900.80 error indicates a problem with the current print job or with a part within the scanner unit of the printer. Please click on the link below to see instructions on how to go about the procedure.

http://bit.ly/qxvmNN


For further assistance, please call Lexmark Technical Support.

Jan 05, 2011 | Lexmark X642e All-In-One Laser Printer

1 Answer

How do i print a report of the usage of my cartridges


The "Device Statistics" under the reports menu will give information on printer and cartrige usage.

Jun 07, 2010 | Lexmark X642e All-In-One Laser Printer

1 Answer

I have a lexmak x75 printer and it wont print only scans


go to the lexmak website download th newest software for printing do this and send me what happened in my mail www.m-o-m@hotmail.com

Aug 17, 2009 | Lexmark X7550 InkJet Printer

1 Answer

How do I change the printing settings from envelope to paper? I have a Lexmark x642e.


I don't have one right in front of me but it goes like this. Press the menu button. Information menu should be in the display..select it...arrow down to paper menu...select..arrow thru till you see paper type...select...scroll thru/arrow till you see the tray or feeder that you want to change..select..then it will give your paper type selections where you can change the setting. Now like I said..I'm not right in front of the printer. I think the paper menu is a sub menu under the information menu...if not it is its own menu below the information menu. Either way....scroll/arrow around a bit and you'll fiind it.
Hope this helps!

Jul 10, 2009 | Lexmark X642e All-In-One Laser Printer

1 Answer

Cant find counter on my lexmark x642e can any one help, I have no manules .thanks


Maintenence counter is in Configuration Mode.
Power on the printer while holding down the 2 & 6 buttons. Continue holding buttons for 20 seconds. You will find the counter in Maintenence counter and can reset it there.

Feb 22, 2009 | Lexmark X642e All-In-One Laser Printer

1 Answer

Lexmark x642e MPF Reset maintenance counter


Power printer off. When printer is powered off, hold down the check button and the right arrow button and hold these down while powering printer back on. Hold the buttons down for 10-20sec....

When printer is finished you are at the config menu. Hit down once, and you will see reset maint counter. Hit menu twice... and you will see resetting...

Then hit back twice to get to the main menu and use your up/down arrows until you see exit config menu. Hit enter and it will reboot printer back to the regular menu.

Feb 02, 2009 | Lexmark X642e All-In-One Laser Printer

2 Answers

Lexmark x642e MPF Reset maintenance counter


Hi~
You can reset the maintenance count by going to the Configuration Menu.

Step 1: Turn off your X64x printer
Step 2: Hold the 2 and 6 buttons while the printer is off
Step 3: Turn on the printer but don't release the buttons yet. Keep holding those buttons for about 10 secs
Step 4: On your Operator Panel, you should see "Configuration Menu"
Step 5: Scroll down and look for "Reset Maint Count" and select it.
Step 6: Exit Config Menu and powercycle your printer (turn it off then back on)

Hope this is helpful... =)

<<ichtuscheeky>>

Jan 30, 2009 | Lexmark X642e All-In-One Laser Printer

1 Answer

Print unreadable


i need driver for printer lexmak z32 for s.o. windows 95.
Please helpme!!

Karen
karenarones@hotmail.com

Jan 20, 2008 | Lexmark Color JetPrinter Z32 InkJet

Not finding what you are looking for?
Lexmark X642e All-In-One Laser Printer Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...