- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
I'm sorry that the Camera
is displaying the error message. "TURN THE POWER OFF AND ON AGAIN"
displays on the LCD screen when the Lens Mechanism is stuck or when affected by
any malfunction. If turning the power on and off again does not resolve the
error message, try doing a power reset. Please follow the below steps to
perform a power reset.
·Turn off the camera.
·Remove the battery pack.
·Press and hold the power button for 30 seconds.
·Allow the camera to remain without power for 60 seconds.
·Reinsert the battery pack.
·Turn on the camera.
Also tryinitializing the Cameraif
you're able to access the Menu items on the Camera. The Initialize option will
be available underSetup or Main settingsSub
If the issue persists again, service is required.
Pleaseclick hearto locate
the service center near your area.
Thanks for understanding. Please let me know if
your require any clarifications.
Hi there please follow the steps and let me know the result.
1. Ensure batteries are fully charged & clean the battery connector point in side the battery compartment.
2. Look carefully between the lens and the camera body for any sand, dirt or any damaged etc.
3. Try turning the camera with the lens facing down and shake to dislodge anything stuck
4. Try removing batteries and memory card, wait 5 minutes and refit the battery only.
5. Now turn on camera( with out card ) and see ,if working then fix the memory card & again turn on the camera. If working then fine .
Otherwise format the memory card and fix back in camera again & try. Make sure before format the memory card take a
back up all photos in your computer then format. If no luck then reset or restore the camera setting by pressing Menu key for 2 sec ..
in not done the press both Menu & self time key for 2 - 4 sec.
i hope it will gives you success. Thanks & Before you leave, if you have found my information helpful and if you haven't
already done so then please press the ACCEPT button, this is how I am paid for helping you today. POSITIVE feedback & bonus is appreciated
You may have inadvertently pressed the DISP button. This turns the display or screen on/off.
The button is probably the up button on the back. try holding that in when the camera is on.
Hope this helps.
Remove the camera memory card and format it. Then restore the camera settings and insert the memory card. Now try. I hope your problem will solve then. If not then your camera CCD is damaged and you need to replace the CCD for the camera. Thank you.
We see this camera often because the lens gets compressed some how and the plastic gears which drive it become damaged, this would be the "buzzing" noise you're hearing during power up. The camera is not passing its power up diagnostics and therefore it shuts down.
The lens is not cost effective to replace on this camera, parts and labor exceed a replacement units cost.
Hope this is some help. Good Luck
If an aperture of "00" is displayed on the camera's LCD panel, perform the following steps in order. Check after each step to see if the problem remains, and proceed to the next step if it does. (In some cases, you may see "Err 01" displayed on the LCD panel.)
1. Check if the lens is correctly mounted on the camera.
If no lens is attached to the camera, "00" will be displayed for the aperture value.
2. Clean the lens contacts.
Turn the camera's power switch to OFF, and then detach the lens from the camera to clean the contacts.
Use a blower to blow away dust on the lens.
Do not touch both the camera's or lens' electrical contacts with your fingers while cleaning the lens.
Turn the power switch to ON again and check the aperture value displayed on the LCD panel.
Refer to the Instruction Manual provided with your camera for instructions for detaching or mounting the lens.
Also, prevent any foreign materials or dust from getting into the camera through the lens mount, and be sure not to damage the contacts.
3. Remove the battery pack.
Turn the camera's power switch to OFF and remove the battery pack. Then reinsert the battery pack, and then turn the power switch to ON again.