Question about Whirlpool 8572546 Duet Sport Stacking Kit

1 Answer

How to replace whirlpool washer Drum, baffle

I I have a 2 years old wirlpool Duet front washer ,one of the bafflels in the drum is broken .I wonder if any one would know how to replace it ??

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Just order a new one from an online parts store and put it in.  The new ones dont screw from behind.  They just snap in. By the way, the rest of the baffles will break as well. So you may as well by a couple.  But there not cheap-You can order them through Sears and pay 23.95 each.

Posted on Mar 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F & 5 flashing, clothes not drained


don' t remove back!  top comes off and drum can be spun  to access each of impellers in drum.

Jul 22, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Very loud roar when spinning 2 years old


Could well be drum bearings quite an expensive repair, if you remove the belt and turn the drum by hand it should be quiet if not then drum bearings worn....

May 11, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

How do you clean out the baffles filled with lint in the Whirlpool Duet dryer?


To remove the dryer drum baffles on a Whirlpool Duet, follow these steps:

1. UNPLUG the dryer.

2. Remove the top panel of the appliance by removing the screws that hold the panel in place in the rear of the dryer. With the screws removed, the panel will slide back, then lift off.

3. Locate the bolts that hold the baffles in place on the outside perimeter of the drum. There should be 2 for each one.

4. Remove the screws for the baffle and it will come off.

HELPFUL HINTS:

1. Remove ONE baffle at a time so you can use the remaining baffles to turn the drum manually.

2. Drum rotates in a clockwise direction.

3. When removing or reinstalling each baffle, duct taping it place will keep it from flipping around when you get to the last bolt holding it in place. It will also keep it from dropping in the drum when removing, and help you hold it in place to reinstalling.

If you have any questions, please let me know. I hope this helps you.

Feb 07, 2010 | Whirlpool Duet Sport 6.7 Cu. Ft. Gas Dryer

1 Answer

Whirlpool duet washer, inner stainless drum rubs


This sounds like a worn bearing housing or the bearing itself has packed up,either way you would have to strip and check these and replace what is broken

Dec 28, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool Duet dryer - "burn marks", "out of round" drum


It's not really BURN marks - it is the adhesive used to affix the felt. You can substitute for silicone to remedy this problem.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 07, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Whirlpool duet dryer felt seal replacement


The drum may to be removed to install the new felt gasket but the old drum can then be reinstalled. The felt gasket seals the joint where the drum rotates at the inside back panel. It is likely that the inside back panel can be removed when the dryer is placed front-down and the outside back panel is removed. In that case the drum does not have to come out.

Jul 08, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool Duet Front Loader won't get up to spin speed


Careful of overloading the front-loading washers. Too much of this will result in the bearings in the drum to go bad. When this happens, the rpms on the drum slow down due to belt slack. You can only see this with the back off of the unit and in the middle of the cycle. They do not sell replacement bearings...you'll have to buy the whole drum (bearings pressed inside) and for 1/2 the cost of a new washer. I hate front-loaders. I'll never buy one again.

May 20, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Baffle came loose from drum...how do I


there are 3 Tork screrws on the back panel that will allow for you to slide the top back and get access to the top of the drum

May 29, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Baffle broke off


Hi, one of our baffles broke recently and I ordered a replacement kit from http://www.appliancepartspros.com/

Here is the link that will take you directly to the page:

http://www.appliancepartspros.com/Appliance-Parts/WHIRLPOOL-Baffle-kit--3-pack-item-number-AP3769371.aspx

Dec 30, 2007 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Replacing the fins on Duet whirlpool washer


most paddles are removed by grabbing hold of the paddle and pull towards the front of the washer which should release them youll need to lift it out when you have pulled on them love

Sep 12, 2007 | Washing Machines

Not finding what you are looking for?
Whirlpool 8572546 Duet Sport Stacking Kit Logo

1,219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

prem mathew

Level 3 Expert

662 Answers

yadayada
yadayada

Level 3 Expert

71043 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...