Question about Bruder Cat Skid Steer Loader

1 Answer

Skidloader stops in it tracks

Skidloader lights blinks three times and hydraulics stop working and blinks three time

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 435 Answers

Check out for the hydraulic oil filter

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bleed the hydraulics on a Bobcat 751 skid steer loader?


Hi Joseph:
Usually hydraulic components will "self clear" any air in the system just by trying to cycle through the functions a few times.
Have to ask the question............
Did you remove and replace the hoses one at a time, or did you take them all off at the same time?
The reason I ask is............ Could there be a remote possibility that any of the hose onnection locations were switched?

Sep 23, 2015 | Dolls, Playsets & Toy Figures

1 Answer

I put the car on the track and put in my controller but it won't advance


One car on track runs great. When I place second car on its track, it stops. I tried to interchange cars. Both cars work on inner track. Both stop on outer track.

Feb 17, 2014 | Carrera Go!!! Nascar Electric Race Set

1 Answer

On my rc volitaion remote on the top the gauge what dose it mean when it flashs


It's in a safety start up mode so there is no accidental start up of the helicopter
while holding model in your hands to turn it on or plug battery in. When ready to fly move throttle
gimble to full up then back down to stop. Light should then stop blinking and the
next time you move throttle gimble up the helicopter rotors should begin to turn.

Oct 06, 2011 | xheli 9053 Outdoor Volitation Metal...

1 Answer

My S107 worked fine the fist 5 minute flight. On my second attempt nothing would happen. The green light on the controller just blinks. Occasionally when I turn them both on the chopper just takes off...


Seems like your controller is not working. Try to change its batteries.
With new batteries try the following:
1. Turn the controller ON. Wait until green light stops blinking.
2. Turn the helicopter ON.
3. Give it throttle few times until it starts working.

Sometimes controller can still work even if has a blinking light. But these cases are very rare.

Mar 23, 2011 | SYMA Toys industrial New Syma S107 Radio...

2 Answers

My sharpshooter and remote both turn on, but the helicopter does not react at all, what should i do?


I had this problem yesterday as well :)

My helicopter charged once worked and flew once for about 5 minutes. Then the helicopter stopped responding to the controller and it wouldn't take a charge. When I connected the remote to the helicopter the CHG light came on solid for about 30 seconds. This means that the controller is waiting to be plugged into the helicopter.

A couple of points to check before you go further:
1) make sure that the helicopter is turned OFF before charging!
2) When charging the red CHG light will blink.
3) When finished charging the red CHG light and the green Power light will blink at the same time.
4) After a certain amount of time both lights will stop blinking to save the batteries.

After taking the helicopter apart this is what I have found:
*The helicopter has a 140mA-H 3.7V Li-Po battery.
*The battery has a little board with 2 tiny computer chips. When the battery is empty these 2 chips will completely disconnect the battery. This prevents damaging the battery and this is why the helicopter stops responding when the battery is empty.
*There are two connections between the battery and the little board - a long connection which wraps one time around the battery and a short connection. My problem was with the short battery connection.

Solution --The little board has a short piece of foil which connects to another short piece of foil on the battery. These two pieces of foil are simply pressed together and then glued. In my case this connection broke. To fix the problem I removed the yellow tape and glue and used a soldering iron to solder the 2 foil pieces together. Make sure that you put tape (any household tape should be OK) back on the battery to prevent any shorts.

Dec 26, 2010 | Master Heaters Air Hogs Sharp Shooter...

1 Answer

Kato locomotive doesnt run. Goes for a short time with spray of contact cleaner then stops


That means that your track is dirty. Your locomotive is picking up dirt from the track, which builds up. on the wheels. Use a track cleaner NOT alcohol... the alcohol does leave a residue on the track after it dries.

Jan 10, 2010 | Kato N Scale, Amtrak P42 Superliner Train...

1 Answer

863 stops in tracks


When all movement of the machine stops the B.I.C.S controller ( under your right elbow )is detecting a " safety " problem. When you get in the machine, turn the key switch to " on , turn and look at the B.I.C.S controller lights. They need to come on in sequence. Only lamp lit now is the seat, pull down seat bar, and that lamp should light. After you push the button to operate, the other 2 lamps should light. Once in the machine, bar down and it ready to travel, use your arms and raise yourself OUT of the seat about a couple of inchs, if the seat light goes out, replace the seat switch. Also ( will need to raise the cab ) check that the seat switch plunger bolt it tight. If it is loose and not holding the magnet in a fixed poistion, now lighned up with the switch that detects where the magnet is, the B.I.C.S controller thinks the OPERATER bounced out and WILL stop the machine. I think it takes aprox 3-10 seconds to make the ecm re-act to the " NO OPERATER " signal Good luck..

Mar 08, 2009 | Bruder Cat Skid Steer Loader

Not finding what you are looking for?
Bruder Cat Skid Steer Loader Logo

Related Topics:

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bruder Dolls, Playsets & Toy Figures Experts

Iron
Iron

Level 3 Expert

3018 Answers

ptpumpman

Level 3 Expert

406 Answers

Marc Taylor

Level 2 Expert

124 Answers

Are you a Bruder Doll, Playset and Toy Figure Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...