Question about Konica Minolta DiALTA CF910 Copier

1 Answer

What does error code c0660 relate to on the Minolta CF1501

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Konica Minolta Master
  • 990 Answers

Hello sir; Turn power off, remove the glass, push scaner unit for and back see have anything stock over there, otherwise you have to change home position senser.

Posted on Apr 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CF1501 error code c0650


C 0650 Scanner home sensor malfunction.
Remove the original glass and clean the home sensor(the sensor is dirty,paper dust) located in the rigth rear corner.Move the mirror assy to maximum right position and you located the sensor.

Feb 13, 2013 | Minolta CF1501 Copier

1 Answer

Como resetar tarjeta minolta cf1501


A que tarjeta te refieres????????
Si es para reiniciar los chips de las unidades de imagen ponte en contacto conmigo.
victor
victor-ipdigital@hotmail.com

Jan 07, 2011 | Minolta CF1501 Copier

2 Answers

My Minolta CF1501 is showing error COF 34


Before doing above open and close the front door. The code is for the Auto Toner Density Control the black image unit if it comes back after opening and closing the front door the image unit needs replacement. You can't change the developer it is all one unit. the fuser has a different code 500 series. Dont mess with gain let machine run stablize.

Dec 24, 2009 | Minolta CF1501 Copier

1 Answer

Minolta EP4320 - How to clear the "Cd" error code


A "CD" code means some thing is not closed correctly or attached correctly. It has been a very long time scine I worked on one, but I believe that when you added the duplex unit there is a bottom part of the duplex unit that is held on with two screws at the bottom and one shoulder screw at the top. From what I remember is that if the bottom part of the duplex unit is not flush withe copier stand and the top part of the duplex unit the joggers will not move and there is a sensor flag that get stuck in the bottom part of the duplex unit. Also, di you connect all of the connector for the unit that goes inside the copier it's self. You are dealing with a copier that is over 10 to 15 years old. Good Luck

Feb 16, 2009 | Minolta CF1501 Copier

1 Answer

Minolta CF1501 Duplex Unit problem


yes you can use it without using the double sided option single only to repair need to replace door you can get a used one not so much $ call me 310-930-6348

Jan 02, 2009 | Minolta CF1501 Copier

1 Answer

ERROR CODE C0660


This is a scanner problem, try the following...



C0650, C0660
Step Check Item Result Action
1 Scanner can be moved manually.
NO Correct drive coupling (Scanner
Belt tension, pulley operation,
drive cable tension)

2 Scan motion: initial scan motion after the
Power Switch has been turned ON or Front
Door has been opened and closed.
NO Carry out misfeed/malfunction
troubleshooting procedures.

3 Connectors are connected properly on
Scanner Motor Drive Board: PWB-IC
PJ1IC, PJ2IC, and PJ3IC.
NO Check connectors for connection.

4 Scanner Motor turns when the Start key is
pressed.
NO Check connectors for connection.
Change motor. Change
Scanner Motor Drive Board.

5 I/O check for Scanner Home Sensor: the
voltage across PJ6C-2 on Image Processing
Board and GND is DC 0 V (home position)
when the sensor is blocked and DC 5
V when the sensor is unblocked.

YES Change Image Processing
Board.

NO Check sensor for installation.
Correct detecting plate.
Check sensor connector for
connection. Change sensor.

6 “IR Area” check:
Malfunction when Power Switch is turned
ON after “Top Image” has been set to 0 and
“FD-Mag.” to 1.000.

Apr 03, 2008 | Minolta CF2001 Copier

1 Answer

Minolta CF900 error C0660


There should be a lamp regulator PCB check the fuse on it. Also, if you move the scanner out of HP will it find HP again? Also, how offten does it show up scines the last time?

Feb 20, 2008 | Printers & Copiers

1 Answer

Getting a error code C0F37 on a Minolta Dialta CF1501. What's the solution to solve this problem. Is it a Black Imaging Unit or ? Marino


Abnormally high toner density detected Black ATDC (auto toner density control circuit)

Replace black IU, check toner motors, make sure toner is loose not clumpy. Change dev reset toner level.

Nov 17, 2007 | Konica Minolta DiALTA CF910 Copier

Not finding what you are looking for?
Konica Minolta DiALTA CF910 Copier Logo

Related Topics:

302 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Printers & Copiers Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

5695 Answers

David Burkhart
David Burkhart

Level 2 Expert

207 Answers

George Mclaughlin

Level 2 Expert

330 Answers

Are you a Konica Minolta Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...