Question about Toilets & Bidets

1 Answer

IS THE FLOAT ASSEMBLY (Mfg. p/n 08204) available

IS THE FLOAT ASSEMBLY (Mfg. p/n 08204) FOR THE THETFORD AQUA MAGIC III toilet available and is there any remove and replace instructions available?


Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Follow the link above. This is where you will find the manuals to your RV toilet. You will probably find everything you need here are at least a phone number to speak to a real person. Good luck and I hope I was able to answer your question.

Posted on Mar 20, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Change float level

Possible float adjustment is stripped. Replace float assembly. Or float is making contact with tank or flapper. Observe when flushing and turn assembly to operate freely position and tighten assembly nut under tank to secure.

Mar 11, 2013 | American Standard 4112 Bone Toilet Tank...

1 Answer

How to fix the pedal flush on a Tetford Aqua Magic IV

I saw the other answers and what are they talking about. thetford is a rv toilet the two bottem pedals are control by cable one cable broke You just have to get pedal repair kit pull toilet out and repair I have a repair kit coming as we speak exact same problem

Apr 16, 2012 | Thetford Toilets & Bidets

1 Answer

Flush pump not working

Unless the inlet pipe has dropped off the pump assembly or got a blockage in it then you may need to replace the pump bellows.
Here is a link to a schematics pdf with all relevant part numbers. These parts are readily available from most camping and caravan equipment suppliers.

Feb 22, 2011 | Maximum Thetford Porta Potti 365 Portable...

1 Answer

Bought a aqua option toilet dual flush from American Standard the tube that usually goes into the overflow tube now rides on a float which rises with the level of water as it gets closer to the overflow...

i have the same issue with my aqua option toilet. if you have a water shut off installed on the supply line to the toilet, just close it enough to reduce the supply pressure. no more splashing.

Nov 17, 2010 | American Standard Toilets & Bidets

1 Answer

My toilet is sweating extensively, leaving puddles on the floor. I am getting ready to install a foam insulation kit, but I don't know how to remove the float and stem.

Condensate can build up around the outside of a toilet bowl and that's often referred to as "sweating".
Condensate is caused when the air is very humid and an object (in this case, the toilet tank) is colder than the air.
Look up something called "dew point"; that describes the point at which the water that is suspended in the air will start to condense on cooler objects.
Dehumidifiers and refrigeration type air conditioners can help reduce condensate.
You can remove the float and stem by doing the following:
1. turn the water off and flush the toilet . Hold the handle for a while to make certain that you get as much water out as possible, then remove the rest of the water using a towel or whatever means available.
2. Look where the water supply line feeds into the tank. There should be a nut that holds the pipe to the tank. Remove the nut then carefully move the pipe a little out of the way... not much.
3. There should be ANOTHER nut that attaches the float assembly. Remove it and note where the rubber washers are. You may even want to replace the washers when you're done, to make certain that the tank doesn't leak.
4. When you remove that nut, the float assembly may stick a little, but gently work it "back and forth" a little and you should be successful.
Good luck

Sep 11, 2010 | Jacuzzi Bath Era BK37 959 White toilet...

1 Answer

My toilet handel is ican install

Remove the water cover lid then remove the chain connector at the handle looks like a diaper pin then unscrew the nut holding the handle in place and feed the handle assembly threw the nut and buy new handle assembly and replace. IF it's just the chain is broke replace the chain they are sold separately at any hardware store. IF it's the valve you can replace it as well by shutting off the toilet water valve, next disconnect the hose and go buy a float assembly that is similar. Adjust the new float assembly to be the same length as the old one then install gasket on the float and put in the hole for the float, install second gasket on the float on the outside and then install the nut and install the hose. Before you tighten the nut on the float make sure the float valve lines up with the handle and the float then tighten down hook up new chain and tighten the water hose, tighten the nut on the float and open the water valve. Watch the water level fill up if it looks like it's going to run over you will have to adjust the float so that it does not run into the throat of the toilet.

Dec 10, 2009 | Mansfield Plumbing Products Mansfield...

1 Answer

Power flush will not flush when handle is pressed down......

pull the lid off the toilet, disassemble the toilet handle mech and take the cartridge out of the big black tank under there. the cartridge should be available at any local plumbing parts house. let me know if you have problems

Jul 02, 2009 | Eljer Aqua-Saver Toilet Actuator -...

2 Answers

I have a 10-year old 2-piece Eljer 1.6gpf (not sure of the model number). The water keeps hissing and does not stop, unless I give the float a little ****. After a long time the I hear water drops coming...

There could very well be salt buildup on the parts that could be cleaned off. Also, if the toilet is not flushed multiple times each day, algae can build up on the shaft, which you could also try cleaning off. Take a peek around the float assembly, and you should see a screw or clip that stops the piece from dropping down. Try releasing the screw or clip, and move the float down, but only a tiny bit at a time. You'll have to experiment a little, maybe moving it several times, but you'll eventually find a good spot. If none of these steps work out, let me know, and we can work from there.

Jun 07, 2009 | Eljer Aqua-Saver 12" Two-Piece...

1 Answer

Need take out thetford toilet of ace award

can anyone tell me where is the fuse fits under a thet ford cassette toilet model ppc2r and wot size

Apr 27, 2009 | Maximum Thetford Porta Potti 365 Portable...

Not finding what you are looking for?
Toilets & Bidets Logo

Related Topics:

650 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toilets & Bidets Experts

john h

Level 3 Expert

7167 Answers


Level 3 Expert

4331 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you a Toilet and Bidet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides