Question about Sony NTX-2135 DHD 2 Channel Car Amplifier (600 Watts) Car Audio Amplifier

1 Answer

I just need to know if the 2 channels from the amp go to the front or rear speaker location on the stereo and if they go to the rear do I hook up the rear speakers directly to the amp and the fronts to the stereo?

Posted by on

  • martsco1 Mar 08, 2009

    I knew alll that but the problem is always the same, you have a 2 channel amp and a 4 channel system... so , since the front speakers are smaller and cannot handle the wattage its obvoius I would tone down the wattasge to them through the amp but, if Ive only got 2 channels Ive got nowhere to put 2 more unless I buy another 2 channel amp or , i wire the fronts with the rears, then I have no control and no fade..... so a solution would seem to be... put front speakers to stereo and rear speakers to amp and pray that you can fade good enough to hear all four. Which also seems a waste of money because you'll be back where you started. so, because I'm an electrician and not a technician my only real solution would to be ... place front and rear left to one channel, and front and rear right to another, then Ive gotr no fade and no control over how many amps push those lil 3" pyle drivers...???



  • martsco1 Mar 08, 2009

    ty, that's the solution i had in mind as well but just wanted to allow someone who knew about these things to give me advice and it is right on track. I have a hard time wodering why companies make things that are not functional or practical for many applications, and would think that sony would perform and fabricate an amp that has 2 channels set up for the rears and 2 channels set up for the fronts, allowing the customer the ease of making an install time shorter, adjustment time would auto and none needed, and all functions would work as they should without installing another device to do it... customer would have adjustments ( that came with his or her unit ) at their fingertips and not have to get under the seat every time another song came on...

    but Ty for your help keep up the good work... I didnt spend a penny on this whole thing, so it is worth the price to spend the time...

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 55 Answers

The only thing that hooks to the stereo are a remote cable should be labeles on the amp. and the rca cables (red and whites) the different channels go to different sets of speakers.right to right left to left. make sure your amp is grounded well or you'll throw the fuse. Hope this helps if you have questions contact me.

Posted on Mar 08, 2009

  • artbesio
    artbesio Mar 08, 2009

    Only logical thing I can think of for you to do is to only wire the fronts directly to the stereo and let that push those. hook the rears to the amp and you should be able to make it sound decent by playing around with the settings on the amp. Most amps you can level those speakers right from the amp. Try doing that and turning them down on the amp and let the stereo push the fronts. it's about the only way it will work. most of your sound is always coming from the back anyway as far as bass and low range. The fronts would then only be used for mid and highs which is okay.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram ford f350 04 for radio need color codes


2004 Ford F350 Truck Car Radio Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Light Green/Pink
Car Radio Accessory Switched 12v+ Wire: Black/Violet
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Light Blue/Red
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger: Blue
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Light Blue/White
Left Front Speaker Negative Wire (-): Orange/Light Green
Right Front Speaker Positive Wire (+): Dark Green
Right Front Speaker Negative Wire (-): White/Light Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Tan/Yellow
Left Rear Speaker Negative Wire (-): Gray/Light Blue
Right Rear Speaker Positive Wire (+): Brown/Pink
Right Rear Speaker Negative Wire (-): Orange/Red

Jan 04, 2010 | Car Amplifiers

1 Answer

I have 2 6x9 speakers up front 4 6 1/2 3-ways


Hello rjmiller4039,

Although amps with 5 channels are pretty rare, you can get one. Alpine, Boston Acoustics, Infinity, JL audio, MTX, and Polk all have 5-channels ranging in price from around $350 up to around $1,000. The Alpine PDX-5 will output 75X4 watts RMS for the front and rear stereo channels and 300 watts to the mono sub channel. It is priced at $599.99 at Crutchfield.

Hope this helps.


Sep 18, 2009 | Jl Audio 500/1 Car Audio Amplifier

1 Answer

Do not have a sub output on receiver /do not know which wire to plug into the amp sub input/5 channel amp /have rca output for front and rear speakers


Hello southernbike,

With a 5-channel amp (stereo L/R front, stereo L/R rear, and subwoofer) you only need the two pair of stereo inputs.

You do not say which brand and model of amp you have, but most have an output configuration similar to the Alpine shown in this link. Connect the front and rear RCA's from your receiver, your vehicle speakers to the respective output terminals, and your subwoofer to the 5th channel terminals.

Hope this helps.

Jul 29, 2009 | Dual Car Amplifiers

1 Answer

Legend Amp hook up manual.


Pretty Straight Forward get a 8 or 4 gauge amp wiring kit.

Run your hot wire to the +12V from the battery make sure to install the supplied inline fuse near the battery don't connect to the battery until installation is complete.

Run the REM to your stereo power ant. Wire. if available.

Run the GND to Metal Chassis Ground keep it as short as possible.

Run the RCA Cable from the back of the Stereo to the RCA Inputs or Low Level on the amp.

This amp is 2 Ohm Stereo Stable which means you can connect 2 (4 ohm) speakers in parallel to each channel or 1 (4 ohm) speaker on each channel or you can connect 1 (4 ohm) Speaker in bridged mode.

There are other speaker configurations you could use but you cannot drop the load below 2 Ohm in stereo mode and no lower than 4 ohm in bridged mode.

Hope this helps


Mar 25, 2009 | Legend LA1490 - American Legacy Series 2 -...

1 Answer

Troubleshooting amp setup


You probably need your remote wire re-hooked and make sure the ground wire is good and the remote wire is connected to the right wire(the red wire).

Jan 05, 2009 | Car Amplifiers

1 Answer

Need specs and wiring options


Eclipse 36401 eclipse%20pa36401.jpg
  • 105W x 4 Channel Max. Power Output at 2o.gif Stereo
  • 60W x 4 Channel 0.1% THD at 2o.gif Stereo @13.8V (RMS Continuous Power)
  • 40W x 4 Channel 0.1% THD at 4o.gif Stereo @13.8V (RMS Continuous Power)
  • ChannelFlex Crossover
  • Adjustable High-Pass Frequency (50-200Hz, L/R Independent)
  • Low-Pass Frequency (120Hz)
  • Adjustable Bass-Boost Level (45Hz, 0-9dB, F/R Separate)
  • High-Current, High-Speed Output Devices
  • High-Efficiency, High-Energy MOS-FET Power Supply
  • Audiophile Grade Component Selection
  • Intelligent 7-Way Discrete Protection Circuitry
  • Noise Reduction with Low Distortion & Ultra-Low Negative Feedback
  • High-Level Input - Add on Capability
  • Epoxy Composite PCB
  • 2o.gif Stable Design
Each 6 1/2" speaker will see 40 Watts
Each 6"x9" will see 521/2 Watts

Yes your solution is correct. Front wired in stereo, bridge rear.

Dec 29, 2008 | Eclipse Car Amplifiers

1 Answer

How many speakers can I use?


Hi,
This should work if channel 3 & 4 are bridged at 4 ohm.
channel 1 should be stable at 2ohm
channel 2 should be stable at 2 ohm
You can hook up the right side speakers together ( + with + and - with - ) . same thing with the left side. this will give you 2 ohm each channel. this will cause your amp to run hot (this might be tuff on the amp). It will give you right (2 speakers) and left ( 2 speakers ), no front and rear adjustement if you need to balance your sound. I think you should be better buying another amp for your sub and take your 4 channels for your 4 car speakers. this amp as a rca output that can feed the other amp ( sub amp ). it is possible to do it.

Good luck

Nov 11, 2008 | Alpine MRP-F250 Car Audio Amplifier

1 Answer

Installation


If you've got a standard 4 speaker system (2 front, 2 rear), your best option is to connect both left speakers to the left channel amp output and both right speakers to the right channel amp output. The only thing you lose is the ability to fade the speakers front to back.

Mar 04, 2008 | Legacy - American II: 2 Channel 1200W...

5 Answers

Wiring Diagram for Sony car amplifier XM-554ZR


You can download the installation manual from the link below: http://www.sony.co.id/support/product/xm-554zr?site=hp_en_ID_i It has the following diagram plus other hookup info... Please update the question & let us know if the information given was useful to you - Good Luck!

Aug 14, 2007 | Sony XM-2150GSX Car Audio Amplifier

Not finding what you are looking for?
Car Amplifiers Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Car Amplifiers Experts

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Are you a Sony Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...