Question about Kitchen Ranges

1 Answer

I have described my problem serveral times with no response. you have my credit card #. so once again. In changing the bottom element, the wires that were stayconed to the element fell back behind the oven wall and into the insulation how can I retrieve them

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kitchen Ranges Master
  • 3,361 Answers

You must unplug the range and remove the rear panel to access the wires.

Posted on Mar 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need some instructions how to change the lower oven element in my britannia SI-12T7 cooker. the element has screws that will not unscrew from inside the oven. any ideas?


straight forward to do. undo the screws to the back panel of the oven.
once remove down at the bottom of the oven you will see where the heater element comes through . there are to main feed wires that are pushed on and one earth wire. pulls these off as they are just push fit.
the element its self is a flat plate with 2 self tapper screws undo these and the element will then come out of the front of the oven. you have to lift it on a slight angle so the feet of the element will come through . hope this helps

Jun 16, 2014 | Britannia SI10T6L Dual Fuel (Electric and...

1 Answer

Why doesn't new bottom element come on?


I don't know if this will help but I've had to replace heating elements a few times and once it didn't work after replacing the element. It turns out the short also caused one of my electrical wires connecting to the element to burn out as well. This may not be your same deal but make sure you check the wiring. You can also try using a voltage meter or tester to see if power is going to the replaced element. -hope this helps

Jun 11, 2014 | Hotpoint RB757 Electric Kitchen Range

1 Answer

The top element does not heat up but the bottom one does,


Hello Barry Kirstein - From what you have described it sounds like the unit has a faulty elements or could possibly be experiencing a wiring issue with the EOC. Try resetting the oven by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and if it proves to be ineffective contact a professional to move forward accurately to properly diagnose the unit.

Nov 19, 2012 | Frigidaire FEF366 Electric Kitchen Range

1 Answer

Bottom coil won't heat up, but the top one does when on broil. There are no codes on the control panel. What could the problem be?


you'll have to check the element with a meter to see if it's bad,umplug the machine,remove the screws that hold the element in,slide it out,remove at least one of the wires and read it out with the meter,alot of times you can see a burn mark or a break in the element,if the element is good,look for a broken wire in the back of the unit or the clock could be bad,again you'll have to check with a meter to see if you're getting 240 volts down to the element,be careful you have to do this with the power on.next time send the model number.the only way to tell is get in there with a meter.
YouTube - Range Bake Element Replacement (part #316075104)

Feb 21, 2011 | Frigidaire Kitchen Ranges

1 Answer

Stove shut off and blew breaker. Once reset everything works but bottom heating coil. Had it checked, it works. No burnt wires in the back.


Check the oven switch. The bottom element is the main element while the top one is usually the grill element. If the breaker tripped there must have been an overload somewhere and you are possibly missing a connection or fused wire somewhere else.

Jan 22, 2011 | Kenmore Kitchen Ranges

4 Answers

We have an Amana Range/Oven ARG7102W, Manufacture #P1143347N W. The oven does not heat up to the temp set. We purchased an oven thermometer to check the temp. In order to reach 350 degrees, we have to...


Hi...

A main wire burned off will cause both elements to not heat at the same time. It could be at the back going to one element then jump off and go to the second element. Or some times the manufacturer runs the wiring to the front on the controls, and a 3rd area that they could have a common tie point is right where the power comes into the oven. When this usually happens you'll have ok burners on top and no power completed to the bottom.
OR
It could be a switch that's bad and not allowing power to carry on to your oven controls at the thermostat.
Let me know
Thanks
Smith

Aug 20, 2009 | Kitchen Ranges

1 Answer

Bottom oven element


Yes you will have to remove the back panel , but first shut off the breaker to the stove as one of these wires go directly to the power cord. Normally I would tell you to unplug it but in trying to move it out you may cause one of the wires to touch the frame and ZAPPP you! So please b4 you go farther shut the breaker off. Once you have the stove pulled out, it should have several screws that hold the back on. Not a big deal. Push the element through and connect the wires. In the future be very careful as you are pulling the element out and usually the wires will stay connected and you can replace the element from the front. Just remember to shut the power off first!

Oct 03, 2008 | Maytag MER5775Q Electric Kitchen Range

1 Answer

JBP66G W1AD Oven won't get hot enough


the yellow may be the oven temp sensor?

May 25, 2008 | GE JBP66 Electric Kitchen Range

3 Answers

Need to replace heating element


We have a maytag stove and we cleaned our oven on the self clean cycle a week ago. I used the oven once since we cleaned it. today we went to use the oven again, and the oven will not heat and the broiler will not come on either....seems funny that both would quit working at the same time.....any suggestions....

Dec 05, 2007 | Maytag MER6772 Gemini Electric Kitchen...

1 Answer

Electric Heating Element Not Heating stove


It's not a fuse, but a wire or heating element has burned up. Please TURN OFF the circuit breaker until you repair the problem, or at least until you know what the problem is! You say "in" the stove, so I'm assuming that you mean in the oven. Whichever element it is, whether it's in the oven or on the stovetop, just needs to be removed and checked for continuity with an ohmmeter. Quite frankly, if it IS an element, then you should see a burned-out spot somewhere on it that's pretty obvious. Then you just need to replace the element. If it's a wire, then you will need to repair the wire so that it safely makes contact with the element again. That process is a little more involved than just replacing an element, but let us know what you find. I can describe a wire-repair procedure if need be. ;)

Aug 13, 2007 | Dacor Epicure ERD30 Dual Fuel (Electric...

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...