Question about SIM2 HT300 Multimedia Projector

Open Question

Sim2 HT300E HDMI no picture

When viewing through HDMI, intermittently picture starts to develop several green spots and lines to the extent that it turns blank and signal is lost. If from remote setting is changed to composite instead of HDMI, picture returns. If picture is changed back to HDMI, picture is lost again whilst composite works fine. If after 30 or 45 mins picture is changed to HDMI then it will be fine. Changed and cleaned HDMI cable and sockets but to no avail. Could this be a dry joint?

Posted by on

3 Suggested Answers

  • 130 Answers

SOURCE: My Sim2 Domino 30H has reverted to factory settings: looks bad!!!

uninstall all of it,then reinstall,hope this helps

Posted on Dec 30, 2009

valeantudor
  • 787 Answers

SOURCE: I am having a problem with the color of my HT300

Is the socket firmly plugged in? In most cases, the cable is not plugged in properly and that's what causes the color problem.

Posted on Mar 01, 2011

caroldon
  • 17129 Answers

SOURCE: My DLP projector SIM2 DOMINO

It is possible that the last time this was connected there must have been an higher input applied than is recommeded so that the input PRE_AMPS were loaded to fail.
You need to check with an signal trace on the input to find if an OP-AMP has failed or the LOGIC switching IC had failed.
Need to test using a signal tester and meter.

Posted on Jul 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my picture only black and white.


What is you input source connection type ?
Is it HDMI, Composite RGB or VGA etc ?

Oct 03, 2016 | ViewSonic PJD5123 3D Projector

1 Answer

My DLP projector SIM2 DOMINO D35 is turned on and works normally BUT picture is absent on all of inputs (projector shows NO SIGNAL, green indicators is ON). Sources of signal and cables are in order. What...


It is possible that the last time this was connected there must have been an higher input applied than is recommeded so that the input PRE_AMPS were loaded to fail.
You need to check with an signal trace on the input to find if an OP-AMP has failed or the LOGIC switching IC had failed.
Need to test using a signal tester and meter.

Jul 14, 2011 | SIM2 DOMINO D35 DLP Projector

1 Answer

Projector fails to turn on


check your lamp. if it has bulges, black spots or fogging, replace it. otherwise, its your power supply/ballast.

Jul 15, 2009 | Multimedia Projectors

1 Answer

I have an InFocus SP5000 projector that has started showing a green glow in mid-screen (center). Before I buy a $300 lamp want to know the cause of the green glow.


either the light filter behind the blue lcd panel or the fly-eye lens (both inside the optical engine) have developed a burn spot from overheating. infocus doesn't sell individual parts for the optical engine, and the whole thing must be replaced. but unfortunately, it's the most expensive part of the projector, usually upwards of $2000 (and there's none in stock).

Jun 24, 2009 | InFocus SP5000 Home Theater Projector,...

1 Answer

I have a sim2 ht300 and the picture is upside down. can you help.


Just go in the projector menu and there is a setting from where you can rotate the picture. Joe

Jan 10, 2009 | SIM2 HT300 Multimedia Projector

1 Answer

Trying to update Firmware on a Sim2 HT300


Take it to an Authorised SIM2 service agent . Some things are just not for the DIY

Dec 19, 2008 | SIM2 HT300 Multimedia Projector

1 Answer

Sim2 domino 20


Hi there

I checked the manual of your Sim2 , but they don't even mention the lamp in there.

You already have the front cover off , check if you can see any small screw around the lamp housing. They normally attach the lamp's housing with tiny screws to the rest of the unit.

Apr 24, 2008 | SIM2 Domino 20 Multimedia Projector

2 Answers

Hi def


No I said you dont get Hidef without a HDMI connection

Apr 02, 2008 | Toshiba TDP-S8 Multimedia Projector

2 Answers

Green spots


Hi there

Sounds like you've got a faulty LCD.

Unfortunately it will need replacement before it will get any better

Dec 15, 2007 | Hitachi CP-S225 Multimedia Projector

Not finding what you are looking for?
SIM2 HT300 Multimedia Projector Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top SIM2 Multimedia Projectors Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Jerry Kramer
Jerry Kramer

Level 3 Expert

3904 Answers

Lampdeng.com
Lampdeng.com

Level 2 Expert

729 Answers

Are you a SIM2 Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...