Jensen vm9022 Disable touch screen???

1: Go into AM/FM mode
2: Hit "setup" on the remote control
3: Enter 543210 on the remote,
listening for the beep for each number
entered
4: A new menu will appear. Touch the button that has the hammer/
screwdriver on it in the upper left-
hand part of the screen.
5: Select Brake bypass to "ON" and hit
the "X" near the bottom of the screen. There is the code.

Are they "burned" DVDs? The brake override will only allow video to come through the screen it won't make the unit not read them.

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.

Here is the solution

1/ insert the dvd movie
2/After the disc loads and plays you will seea blue screen telling you "it is unlawful to drive with a movie bla bla bla"
3/Activate the brake sequence and disable the blue screen using the hand brake,the switch method or anything else to give the unit its 3 pulses to disable that freakin blue scrreen.
4/Next,on the main remote press stop twice,then 1,2,6,4.
5/You will now see a hidden menu that says.

Region Code
Brake Override(I know you are droling by now)
Macrovision(Watch all the burned and pirates you want if this option is off)
Loader Version
Model Version

6/Using the right joystick on the unit,navigate to the options of your choice,click on them to toggle
on ,off or witch region code you want.
7/This is what you want.

Region code 1
Brake override ON
Macrovision OFF

When your done,click SYS SETUP on the remote TWICE to save the settings and vingo.

hook your green/white camera override wire to your parking wire that should solve your problem

There is no e-brake override code. You have to hardwire it to bypass the e-brake. Take the peach-colored wire and ground it to metal inside the dash. Put a toggle switch inline on the wire and mount it somewhere you can reach it. When you get the blue screen when starting a movie, open the switch for 3-5 seconds, then close it again to reapply the ground. Your movie will start up, and you can then drive away with it playing.

DVD head units have one extra wire in their wiring harnesses, compared to a standard CD head unit. On mine, it's a peach-colored wire, and is the activation wire for the DVD feature. During the installation, the instructions call for this wire to be tapped into the emergency brake indicator light wire. The reason is this:

The e-brake indicator light is what is called a "ground complete" circuit. That means that the bulb always has power applied, but when you pull the brake, that puts a ground to the wire and completes the circuit, allowing it to illuminate. The head unit sees this ground, and activates the DVD player.

In my Jensen unit, I simply ran this wire to a ground (I used a screw near the fuse box), and I put a switch on the wire, so I could break the ground contact at will. Jensen calls for a procedure to activate DVD playback. In their instructions, they tell you to select DVD from the option menu, and when the "lawyer screen" comes up (the one warning you to park before you watch a movie), you release the e-brake for 3-5 seconds, and then reapply it. To simulate that with the switch I used, I leave the switch closed (activated), and select DVD. Then I flip the switch "off" for 3-5 seconds, and flip it back "on". This tricks the head unit into thinking I put the e-brake off for a few seconds and then put it back on, and the movie will start. Then I can drive away.

Basically, ground the wire that is used for DVD activation, and put a switch inline on it. Then you can break and reapply the ground in whatever manner is required by the manufacturer of your head unit. If there is no off/on sequence with yours, as there is with mine, simply ground the wire to a screw inside the dashboard and you're done.

The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. If you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.

The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. If you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.

The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. If you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.