Question about Memorex MVDR2102

1 Answer

Interface error! Trun off the power

I have the same problems. interface error! turn off the power. panel not working can not manually turn on nor off. nothing working. i need help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Memorex Master
  • 19,396 Answers

Unplug all cables and disconnect power for five minutes.

Posted on Mar 07, 2009

  • Ginko
    Ginko Mar 07, 2009

    Interface error means that there is either a bad cable , or that the input board is faulty.

    To start unplug all cables, including power cable, wait ten minutes, and then re-connect the power cable only, if the error disappears, then one of the connection cables used is bad, if not , then there is an internal fault.


  • Ginko
    Ginko Mar 07, 2009

    If you also have an USB device connected to your Memorex, like a memory stick, that can also be the cause for the problem, you get "interface error" whenever you have a data communication problem, and this is often caused by cables and connected devices.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remote shows no response


I have just had a major problem trying to get the handheld (touch screen) music centre to communicate with the multi room interface. It took over a week to sort out by trial and error, but here is the solution :
1. Disconnect everything from the multi room interface apart from Room A and the CD player (blue connector).
2. Turn off the electricity supply at the wall (turning off any in line extension lead is not good enough - it needs to be at the wall socket). Leave turned off for at least 2/3 hours.
3. Turn back on and then leave it again for 2/3 hours.
4. Touch the music centre and you should find that it has now registered with the interface unit.
5. Connect the other rooms and input sources with the power switched on (contrary to instruction manual which advises you connect everything before powering up).
6. Test each input systematically as you connect them.

Hope this helps. I was on the verge of buying another multi room interface (I have 2 music centres and neither worked so assumed in was the interface at fault), at a cost of £200, so now glad I persevered with resetting the system !

Mar 03, 2014 | Bose LifeStyle 50 System

Tip

Whirlpool duet F70 and F71 error codes.


F70 and F71 are two logic board error codes that point at a communication error between the main logic module and the control pad (user interface and CCU), and between the motor control unit and central control (MCU, andd CCU that is main control module).
Repair is difficult, as motor, wiring and voltages from control modules must be tested.

Try first doing a reset, by disconnecting power cord or tripping circuit breaker and leaving power off for five minutes.

If that does not help and errors come back, then the best thing to do is calling the service number listed on the user manual.

Here extensive explanation of error codes and relative troubleshooting:

F70: CENTRAL CONTROL UNIT HEARTBEAT FAILURE
If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the Central Control Unit to the User Interface.

1. Check for continuity of the User Interface harness.
2. Check wire harness connections to the User Interface and the Central Control Unit.
3. Replace User Interface if drum is rotating.
4. Replace Central Control Unit if drum is not moving

F71: USER INTERFACE HEARTBEAT FAILURE
If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the User Interface to the Central Control Unit.

1. Check for continuity of the User Interface harness.
2. Check wire harness connections to the User Interface and the Central Control Unit.
3. Replace User Interface if drum is rotating.
4. Replace Central Control Unit if drum is not moving.

To get parts and diagrams try entering the full model number in one of the websites below:

Enter the model number ..

To contact a repairer, call the number listed on the owners manual or use the Fixya directory (US only)

on Nov 05, 2010 | Whirlpool WFW8300SW

2 Answers

Shortly after end of 1 year warranty, KEMS378SSS04 began displaying F6E0 Lost Communication on lower over UI (not on the microwave). Turning power off/on (multiple times required sometimes) fixes the...


Hi,

Below is the complete instruction sheet.

You are having a communication error between the appliance. Here is the actual tech manual instructions for that code:

PROCEDURE: Before proceeding, press OFF, OFF, START to enter Diagnostic

mode and verify the error codes. Ensure AM software, UI software and EEPROM

CHECKSUM versions appear on the lower text line. If AM software and EEPROM

versions do not appear, UI and AM may not be communicating. Verify this for the

lower oven UI and for the microwave (upper oven) UI. The lower oven UI will show

the AM software version for the lower oven appliance manager, and the microwave

UI will show the AM software and EEPROM versions for the microwave appliance

manager.

If the lower oven UI is not displaying the AM software version, go to UI IS NOT

DISPLAYING AM SOFTWARE VERSION.

If the upper oven UI is not displaying the AM software and EEPROM versions,

go to UPPER OVEN UI IS NOT DISPLAYING THE AM SOFTWARE AND

EEPROM VERSIONS.

If lower oven UI and microwave UI are both displaying an error, go to LOWER

OVEN UI AND MICROWAVE UI ARE BOTH DISPLAYING AN ERROR.

UI IS NOT DISPLAYING AM SOFTWARE VERSION:

A. Unplug oven or disconnect power.

B. Open the back panels and make sure the P6 and P2 connectors are fully

inserted on the appliance manager and on the lower oven user interface board.

- If they are not plugged in, plug in connectors and go to step F.

- If they are plugged in, go to step C.

C. Visually inspect all wires between P6 on the appliance manager and P2 on the

lower user interface.

- Make sure wires are not cut or pinched.

- If the wires appear to be intact, perform a continuity check between

P6-1 of the appliance manager and P2-1 of the user interface board.

Complete for P6-2(AM) to P2-2(UI), P6-4(AM) to P2-4(UI) and P6-5(AM) to

P2-5(UI). All the measurements made should be less than 5 ?. If any of

these measurements exceeds 5 ?, go to step E.

D. Replace the appliance manager. Ensure all connectors are properly inserted.

E. Replace the wiring harness (signal). Ensure all connectors are properly inserted.

F. Replace all parts and panels before operating.

G. Plug in oven or reconnect power.

H. Observe for longer than 1 minute to determine if error has been repaired.

I. If error does not appear, initiate a bake cycle. Let the cycle run for at least

1 minute.

- If no error occurs, cancel the cycle, the problem has been repaired.

- If error occurs again, restart the troubleshooting procedure at step A.

At step D, replace the lower oven user interface board if appliance

manager has already been replaced.
- If both are replaced the problem has been repaired.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

May 22, 2011 | Ovens

1 Answer

Shows f70 and the door won't open


First there is a way to open the locked door and get your clothes out. On this model of Kenmore front load washer you can manually release the door lock.Unplug the washer from power. Remove the front lower inspection panel (see the first image), and reach up to the bottom of the door lock and pull down on the small teardrop tab. This will unlock the door lock and allow you to get the clothes out.
The F70 error is a control failure that occurs when a signal from the main control to the interface (touch pad) is not detected.
This can be caused by a loose harness connection at the interface or main control. The image below will show how to remove the top so you can check for lose connections. Be sure to unplug the washer first.
The F70 is an internal control problem. It can be caused by a failed central control board or an interface problem. The way to determine which part is bad when the error occurs is as follows:
  • If the error occurs when the machine is running then the problem is the interface.
  • If the error occurs when the washer is not running the problem is the central control unit.
The control and the interface are available from the following link: Sears PartsDirect . Use your model number to order the correct part for your washer.

Aug 18, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

CE error code on hayward pool heater


CE= Communication Error between Control Module
and Display Interface Assembly
1. Disconnect and then reconnect power to heater.
2. Check for faulty wiring or connection.
Inspect Display Interface Wiring. Ensure Display Interface Plug is securely attached to Control Module. .
3. Control Module and/or Display Interface Assembly
are defective.Replace Control Module and/or Display Interface Assembly.
Here is a linkt oH aywardmanuals:
http://www.haywardnet.com/inground/products/manuals.cfm

Jul 04, 2010 | Hayward 250kbtu Ng Pool Heater - Inground

1 Answer

Radio works intermittenly,Sometimes all day,Then not at all. I have replaced Amp..Worked great for a few days.You think its the radio head unit?


had same problem in a dodge... turned out the interface module was bad. but try a relay on the amp trun on lead. there may not be enough power to trigger the factory amp

Feb 10, 2010 | Metra CHTO-02 Chrysler Pacifica 04-Up...

1 Answer

Dead power supply.


Faulty power-supply symptoms:

The front panel display and buttons are completely nonfunctional and appear dead. The unit will do nothing more than display the following messages on the TV screen:

Interface error
(and or)
Interface error! Turn off the power

If a DVD or VHS tape was inserted prior to the error occurring, you won't be able to eject either from that point further. They'll remain stuck inside the unit until you've completed the repair detailed below.

Interface error! Turn off the power <--- explains how to completely restore your combo in less than 20 minutes by replacing a $1.59 part on the power-supply board. mikeadams110@yahoo.com

Nov 17, 2008 | RCA DRC8300N DVD Recorder/VCR

2 Answers

RCA DVD/VCR model DRC8320


Faulty power-supply symptoms:

The front panel display and buttons are completely nonfunctional and appear dead. The unit will do nothing more than display the following messages on the TV screen:

Interface error
(and or)
Interface error! Turn off the power

If a DVD or VHS tape was inserted prior to the error occurring, you won't be able to eject either from that point further. They'll remain stuck inside the unit until you've completed the repair detailed below.

Interface error! Turn off the power <--- explains how to completely restore your combo in less than 20minutes by replacing a $1.59 part on the power-supply board. mikeadams110@yahoo.com

Jul 15, 2008 | RCA DRC8320 DVD Recorder/VCR

1 Answer

C42UX problem


An unknown printer error has occurred. Turn the printer off, disconnect the interface cable and turn the printer back on. If error disappears, turn the printer off, reconnect the interface cable and turn the printer back on. If error continues then printer needs service. If printer returns to normal the issue is resolved.

Jun 09, 2008 | Epson Stylus C42UX InkJet Printer

2 Answers

Interface error! Trun off the power


Okay...sounds like you have a lot of signal splitting as well as devices that may also weaken your signal. With digital cable, you won't see snow or what would be a dead give-away to a weak signal. Only analog signals do that. Digital signals give you crisp clear picture or they drop out.

Try taking the cable directly from the wall to the DVD-Recorder. If you are able to watch channels and manipulate the device, then you can start from there as the source is good and the recorder is good.

Try to place the DVD-Recorder after the first splitter and see if you still receive stable signal. You'll probably need to leave the unit in this part of your A/V chain.

It really sounds like you need a signal amplifier for all the splitting you've done, or to re-work your A/V stack into something more manageable. It is entirely possible that the built-in tuner of the new DVD-Recorder is not as sensitive as the old unit.

Oct 28, 2007 | Memorex MVDR2102

Not finding what you are looking for?
Memorex MVDR2102 Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Memorex Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72670 Answers

 Grubhead
Grubhead

Level 3 Expert

4861 Answers

Radames Pagan
Radames Pagan

Level 3 Expert

196 Answers

Are you a Memorex Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...