Question about Konica Minolta magicolor 2300DL Laser Printer

1 Answer

My Konica Minolta Printer cuts paper

I have a Konica Minolta Magicolor 2300DL printer that cuts paper in the middle of the page vertical when it comes out. I thought it may be a paper clip or something stuck in there causing it but I can't see anything and I don't know where it rolls from to take it apart to check it further.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

You most likely have a "claw" out of place in the fusing section. These are sharp little spring guided teeth that keep the paper off of the heated roller. If you had a paper jam and pulled the paper out forcefully it can flip these claws out of place, causing it to cut your paper. (or jam more often). To find these claws, follow the heat. They rest on the hottest part of the pressure rollers of the fuser.

Posted on Jul 09, 2009

5 Suggested Answers

SOURCE: Konica Minolta Magicolor 2300 DL - Fatal Error Code 0EH ????

I had the same problem one time, they told me to pull out all of the toner cartriges, power off, power on, power off, replace all cartridges and the problem went away.

Who knows why. If this doesn't work....

Call Konica Minolta tech support.

They were pretty helpful to me.

Dave

Posted on Jan 06, 2008

osiriscompu
  • 16 Answers

SOURCE: Konica Minolta magicolor 2430DL

Open the top cover. Remove the drum (part with long green handle). Below the drum you will see a strip of glass about 4-5 inches long. Take a cloth and wipe across the glass.

This will normally clear up any white lines in your print.

Posted on Jul 19, 2008

  • 118 Answers

SOURCE: Konica Minolta Magicolor 2400W drum cartrige-how to replace?

Did you buy a whole new drum unit, or just change the cartridge? If so, the fuse may still be blown. Also, you may need to empty the spent toner out of the old cartridge.

Posted on Nov 18, 2008

  • 97 Answers

SOURCE: Konica Minolta Magicolor 4690MF gives 0502 error.

The fuser temperature is too high. There is probably some residue from the transparency left on the thermister or the thermister went faulty that causes a wrong reading. The only solution would be to have the printer serviced.

Posted on Aug 05, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How does an automatic feeder detect paper


Hello hope everything is okay coming back to your question on how ADF detects the paper is that on top of ADF of the copier or printer there's apart called ADF tray then under that tray there's a sensor which help the machine to sense that there's a document or a paper.

Jan 13, 2017 | Office Equipment & Supplies

1 Answer

How do I correct error h5 on a Sharp printer AR-5620N?


Hello Sudhir,
The error code H5 means there was at least 5 pages in a row where the paper did not come out of the printer correctly (most likely paper jams. The following manual will direct you on the steps needed to clear the code, please note especially page #8-3
Service Manual SHARP AR 5618 5620 5623 SME

The following video should help also;

Jan 09, 2017 | Sharp Office Equipment & Supplies

1 Answer

Bizhub C250 using to much toner. Images are very dark. Ink can even be rubbed off pages. How do you adjust?


Check that the fuser is not in enevople mode. two green handle up not down. check the files

Oct 28, 2016 | Konica Minolta bizhub C250 All-In-One...

1 Answer

How to set two sided printing in konica minolta pagepro1390MF


It might be better to place this problem in the computer section.

Oct 17, 2013 | Office Equipment & Supplies

1 Answer

Error code 3501


HI
I HAVE KONICA C6500
ERROR CODE 3501 and 3802 but know the error 3501
I know it rech high temperature I change the sensor 1 UP fuser roller
and I reset the error, the machine start and stop again with error 3501

Oct 01, 2013 | Konica Minolta Bizhub C 6500 Copier

2 Answers

I can't figure out how to feed paper into the printer


hello

i assume you refer to ML591, dot matrix ?

go to this link, and download users guied and/or manual http://my.okidata.com/PP-ML591.nsf?opendatabase

how feed the paper http://my.okidata.com/PP-ML591.nsf?opendatabase

Jan 11, 2011 | Okidata 591 Printer

3 Answers

Paper jam error but no paper in printer


If you want technical help regarding Okidata Printer, you can contact us on Okidata Printer support1-877-7788969 any time. We are always here with technical team for your help. For further information, click on http://resolit.us/Okidata-Printer-Support.html

oki5-wjnoyh3savnbf4ovvwadbyke-4-0.jpg

Jun 25, 2009 | Samsung OKIDATA - OKI C5200n - Printer

2 Answers

Paper jams consistely and then continues to feed, even if only printing one page


check your paper size setting on your print menu. i had this problem when i set the paper size smaller than the printer is able to handle (3x5 card) ... i just switched to 4x6 and don't have any problems.

Oct 24, 2008 | OKI C5100n Laser Printer

2 Answers

Okidata Microline 30 Turbo dot matrix


The problem your having is a spacer motor. It's located under the carriage that holds the ribbon/printhead. The part number is 56513701. Available at Seattle Platen - Dale 1800-221-2388.

Here's a free copy of the Okidata 320T service manual that will walk you through testing and verfying before ordering the replacement part.

If this helped you, please hit me up with a FIXYA. Thanks.

http://www.feedroller.com/Store/Service%20Manual/SER320T.PDF

Aug 30, 2008 | OKI MICROLINE 320 Turbo Matrix Printer

2 Answers

Okidata Model# GE5253P


An online manual here: http://my.okidata.com/PP-ML320.nsf?opendatabase There is probably a top of form setting which needs to be checked & corrected. I assume you've checked tab/margin settings in your software & printer setup?

Sep 28, 2007 | Matrix Okidata Microline 320 Printer

Not finding what you are looking for?
Konica Minolta magicolor 2300DL Laser Printer Logo

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

5729 Answers

David Burkhart
David Burkhart

Level 2 Expert

207 Answers

George Mclaughlin

Level 2 Expert

333 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...