How can I to control multiple HDTVs in several different rooms via a HDMI matrix switch?

HDMI Splitter 1x4 offers HD video solution for supermarkets, shopping malls, HDTVs, STB, DVDs, projector factories, data control centers, information distribution, conference rooms presentation, education and training, corporation showrooms, home theaters and more. Amazon com MALLCROWN 4 Port 1080p HDMI Splitter with Ac Power adapter...

http://lsm-video.en.alibaba.com/

3DHDMI Splitter, 4k HDTV SPLITTER
3DHDMI Switcher, 4k HDTV SPLITTER
3DHDMI Converter,Audio

Splitter,Audio Converter,Audio
Matrix and others AV Products.

You are welcome to contact us today.


Duke Chu

is the splitter rated for 3d??

HDMI is a high bandwidth digital signal and you cannot cascade multiple HDMI Matrix units. It will degrade the video quality and you might run into EDID and HDCP issues. For further queries visit KVMSwitchTech or Call at 866-865-7737 (TOLL FREE).

Step 1:

Connect the audio/video input of the component cable into the "A/V" port located on the back of the xbox 360

Step 2:

Match the red, blue and green cables on the other end of the component cable to the corresponding component ports on your HDTV. If your HDTV has more than one set of component inputs, make note of which one you use.

Step 3:

Slide the switch on the component cable to "HDTV."

Step 4:

Turn on your HDTV. Set the video mode to the component port that will be used. HDTVs with multiple component ports will usually be labeled "Component 1," "Component 2" and so on

Step 5:

Turn on the Xbox 360. Go to "My Xbox." Select "System Settings" then "Console Settings" then "Display" and then "HDTV Settings." Choose the display setting (720p, 1080i and 1080p) that is best compatible with your HDTV. If you're not sure, try them all until you find the one that looks best.

Step 6:

Disconnect any previously connected A/V or component cables.

Step 7:

Connect the HDMI AV cable connector to the "HDMI AV" port on the Xbox 360.

Step 8:

Connect the other end to an available HDMI port on your HDTV. If your HDTV has more than one HDMI input, make note of which one you use.

Step 9:

Turn on your HDTV. Set the video mode to the HDMI port that will be used. HDTVs with multiple component ports will usually label them "HDMI 1," "HDMI 2" and so on.

Step 10:

Turn on the Xbox 360. Go to "My Xbox." Select "System Settings" then "Console Settings" then "Display" and then "HDTV Settings." Pick the display setting (720p, 1080i and 1080p) that looks best on your HDTV.

Loose the splitter and you will be in good shape unless there was damage done you should be good.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

it is not your hard drive
you have to reset the video setting and it will work again Hdmi is different on each tv so you have set this up again ok let's do this with the unit off turn the main switch on the back of the unit connect your Hdmi cable to your tv now place your finger on the front on/off switch keep your finger there ok now turn the mainswitch on the back of the unit the playstation turns on but don't remove your finget yet wait about 4 seconds or until your heard another bip (not the one when the playstation turns on) once you heard this bip remove your finger before the playstation turns off if you let it turn off try again all of this but if you remove your finger on time just wait few more seconds and bingo you have picture again using Hdmi

I have new Panasonic DVD & Combo units stacked on top of each other and had the same problem, until last resort I read the manual and and easily changed the frequency on the DVD unit and remote, you can have up to 3 Panasonic units with different frequencys close to each other.

Suggest using HDMI or Component Video if you can. They provide the best picture quality. Should be able to use RCAs if need to.

Try switching the TV Mode. TV may have multiple modes if you have multiple connections.

yes, hdmi will give you better results..
are you running hdmi to hdmi connection on tv from cable box?
if so, that is correct but as for the dvdr, what tv port are you connecting it to? i would use another hdmi cable for the dvd too for best picture resultif it's an option on your dvd.. you should have multiple input outlets on your lcd with 1-3 options for input devices via analog or hdmi.. so analog is not hdmi--hdmi is digital so it switches to the hdmi resolution when you turn it on..

let me know how it goes and if i was helpful involving resolution.. helpful feedback is appreciated.. thanks, d

your dvd player should be set to a different