Question about Dewalt Tools & Hardware - Others

1 Answer

The disc will not keep spinning - Dewalt Tools & Hardware - Others

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 52 Answers

I am assuming you have a 5" pad palm sander. IF pad stops then belt is broken

Posted on Mar 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Festool RO 125 leaves scuff marks when sanding


depends how important it is to vacuum the dust, most generic brand sandpaper discs will have different hole placements for the sander and the vacuum cant suck the dust up. if you are getting swirl marks from the edge of the sander, is the disc too small? a generic brand that is slightly larger may work but try and keep the sander flat or the excess disk can cause a little trouble with the finish.

Apr 27, 2014 | Festool 492271 5 Inch Stickfix Interface...

1 Answer

Sander disk stops spinning on contact.


It sounds like a gear is worn out inside the sander.
Many of these have a gear or a splined shaft on the end of the motor armature, and the shaft or gear meshes with another to make the disc turn.
One of your gears or shafts has likely worn out.
Sometimes these can be fixed ( I've done a few) , but sometimes the repair parts are either unavailable, or too expensive to make it worthwhile.
Be blessed.

Mar 10, 2013 | Tools & Hardware - Others

1 Answer

I have a pts4 porter cable pneumatic sander that spins but stops on contact with a 100 grit pad or any pad that ive tried and this hapens even at the start before the compressor even kicks on. it didnt...


this unit takes 90 pounds per constant for desired function. Most machine shops have Huge compressors that will run these at a constant rate ,, also check the exhaust ( towards the vacuum hookup to check for clogs,, ) compressors that have a gauge that read 90 lbs doesn't necesarly mean they have the CFM to keep the pressure at what you need to keep it running

May 03, 2011 | Porter Cable PTS4 5 Inch Vacuum Ready...

1 Answer

I have lost the screw that holds the sanding from spinning on its own. I can't find the part number. Could you assist please?


I do not know if this will help because I do not know which screw you need. If you click on the link below you can look at the delta service manual parts list.
http://www.ereplacementparts.com/images/delta/31-695_TYPE_1.pdf

Otherwise can you be more specific on the location of the screw?

Apr 29, 2011 | Delta 31 695 6" Belt/9" Disc Sander

1 Answer

Removing armature from clarke super 7r edger and how to remove rubber backup plate that supports sanding discs.


The rubber backup plate threads on. You can make up a bracket to insert into the 2 larger holes of the plate. You must keep the fan of the edger from turning to unscrew the plate. I use a hard piece of wood or if you are careful, a large screw driver. The plate unscrews counter-clockwise.

Mar 10, 2010 | Tools & Hardware - Others

1 Answer

It spins out of control if I don't keep it under load.


Im not sure what you mean "out of control" but the tool is only meant to be on while in use . If the tool is really going crazy ,pull off orbital and check all screws and tighten accordingly

Dec 28, 2009 | Makita BO5010 5" Random Orbit Sander

1 Answer

Sandpaper keeps come off


probably the typer disk you are using. cheep disks will not stay on long.

Sep 29, 2009 | Bosch Power Tools Sanders Orbital Sanders

1 Answer

Disc pad stops


It could either be that the brushes partially burned I would check to make sure your brushes are in good shape and take it out of the helpers pay ;)

Nov 06, 2008 | Porter Cable 332K Quicksand Random Orbit...

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1378 Answers

john h

Level 3 Expert

7409 Answers

Ron Sanders
Ron Sanders

Level 2 Expert

118 Answers

Are you a Dewalt Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...