Question about JVC HD-52G886 52" Rear Projection HDTV

1 Answer

My screen is black but i ges sound then the red

My screen is black but i get sound then the red and green light starts blinking and then the all tv freezes

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 93 Answers

Have you checked that the lamp is working? If the lamp hours are too high, then the television will no longer function until the lamp is replaced and the counter reset.

When you have replaced the lamp, do this process to reset the timer:

1) Press the Menu button
2) Scroll down to the LAMP TIMER RESET option, scroll right to enter
3) Confirm that it is OK to reset the lamp timer by hitting the OK button.
4) The on-screen menu should confirm the lamp was reset correctly.

Posted on Mar 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The TV was turned off; and when it was turn on later, the green light blinked (while with only black screen w/no sound, or bulb illumination front/back of unit); and shortly afterwards the status ligh


Lamp is possible----

Mitsubishi TV troubleshooting
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Jul 17, 2012 | Projection Televisions

1 Answer

Was watching TV, heard a pop and the screeen went black. Now when I turn it on, the pwoer light blinks green but their is no picture or audio. The light then starts blinking red


Hi,
Is is standby light blinking red or any other light? Let me know how many times red standby light blinking after three seconds long pause to provide you helpful info.
It seems pop sound was due to broken lamp, please check lamp inside tv and if it is broken, replace it to solve tv problem.
Hope this will help.
Thanks.

Mar 09, 2011 | Sony KDS-50A2020 Television

1 Answer

Black Screen no sound, Green light blinks for some time then goes red then recycles back to green


Tv have power LED lights indication are blinking and recycle blinking.Mean the tv power supply board is the problems and the causes.That the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Mar 02, 2011 | Sony KDS-R50XBR1 50" HDTV

1 Answer

My screen is black and sound is off. The green


I have the same problem. Can a bad lamp cause the sound to go out?

Jun 24, 2010 | Sony KDS-55A2020 55" Television

3 Answers

Tv won't turn on. It blinks green then red.


Hi,
Question shows tv is Sony KDF-60WF655.
Green light blinks when tv gets prepare to fire up lamp, check internal circuits then show picture on front screen.
Red light blinking shows some kind of internal problem during circuit check and protection got activated upon some failure.
Count the red light blink as you will see 3 second long pause and post it here to diagnose what section of tv got problem.
Did you replaced its lamp in last 2-3 years?
Thanks.

Jun 01, 2010 | Sony Grand WEGA KDF-60WF655 60" Rear...

2 Answers

Sony kf 50e200a screen goes black and sound turns off for min...


TV has gone into "protect mode" to do just that to protect against the damaging failure that has been detected, you will need a servicer to diagnose the failure. Good luck and Merry Christmas!

Dec 25, 2009 | Projection Televisions

1 Answer

No picture or sound mitsubishi 62525


Capacitor failure is the most likely scenario the FMT ans Signal PWB would cause the picture interference and the power pwb would cause the lamp light to turn red and give a 34 code when the device/ input and menu buttons are pressed in together and held for five seconds. That chassis has issues with every board in the chassis having failed capacitors you can get repair kits for the V26 chassis at the follwing link that come with instructions. Your model is the V26 chassis. Heres the link.
http://servicemanuals.vstore.ca/

Jan 25, 2009 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

PT-60LC13


there are fans inside tv need to make sure they are clean and free of dust

Nov 27, 2007 | Panasonic PT-50LC13 50" Rear Projection...

3 Answers

Sony KP-51HW40 No Picture, only sound


to thus problem its very simple .! try to resolder at the back of the picture tube board.

Nov 26, 2006 | Sony KP-53V75 53" Rear Projection...

Not finding what you are looking for?
JVC HD-52G886 52" Rear Projection HDTV Logo

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Projection Televisions Experts

easy alberta
easy alberta

Level 2 Expert

132 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

Are you a JVC Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...