Question about Spirit Weslo FREE SPIRIT 815 Treadmill Walking Belt

Open Question

Incline has error message for a free spirit MD treedmill

Incline has error message for a free spiritmd treedmill. It tells me to bypass the problem by hitting the stop button. That only allows me to get the thing moving forward but not up and down.

Posted by on

  • Benbuy Apr 18, 2009

    I have Sole F85 and it had the same error message. I opened the motor housing , cleaned the dust, performed calibration procedure, and the problem seemed gone.

×

2 Suggested Answers

maxtreadmill
  • 832 Answers

SOURCE: Treadmill powers off when pressing Incline Increase "br 1" error

You may have a beltand deck problem. Test by the following procedure:
without the poweron stand on the walking belt, push the belt in the, direction it normally turns. If the belt is very difficult to turn (on most treadmill this means that you have high belt/deck friction I first apply silicone lubricant between the belt & deck to see if that clears up the problem. Most problems originate from the belt and deck 75 to 85% of the time

Posted on Jun 13, 2010

  • 26 Answers

SOURCE: Machine shuts off when i press incline up. Belt and board look ok

THis sounds like a controller board problem. In many of the treadmills I have seen the same board controls the drive motor and the incline motor. If this product is under warranty have the company covering the warranty check it out. Anytime you buy one of these machines buy the extenced warranty. I was a field service tech for a warranty company. When you call in with a problem make it sound severe.. I have replace almost everything in one except the frame just to make a customer happy. I am not sure of the error message but i seem to remember it being associated with the controller.

Posted on Jun 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code message


What Does Your Treadmill's Error Code Mean? - LifeSpan

www.lifespanfitness.com/.../what-does-your-treadmills-error-code-mean

Free
May 21, 2015 - If the running belt stops after 6 seconds of starting the treadmill, this may indicate that either the ... If there is no belt movement, or you notice a burning smell coming from the motor area, this ... An E6 or E7 error code is an incline error code. ... This will cause the incline motor to raise the running deck up.

[PDF]ERROR CODES: ADDITIONAL ERROR CODES:

www.gympart.com/TSB/.../Treadmills/.../Sportsart%20Error%20Codes.p...
ERROR 6: INCLINE ERROR - CHECK INCLINE OPERATION AND CALIBRATION. ERROR ... ERROR 1-1: AC SERVO ERROR - AC SERVO MOTOR ENCODER HAS FAILED ... error codes listed by category: treadmills, bikes, elliptical trainers. ...ERR1 Condition 1: Press speed key; walk belt doesn't move; ERR1 appears.

[PDF]Error Code Troubleshooting Guide


Jan 19, 2016 | Exercise & Fitness

1 Answer

REEBOK T 3,2 TREEDMILL INCLINE MOTOR MAKES A BUZZING SOUND AND GETS EXTREMLY HOT, BUT DOES NOT OPERATE.


RUn the software calibration for easy diagnostic, and fix it.
Go under the HOOD motor, and see the steps . or see the steps
God bless you
The Steps for Newer Style Console Calibration:
  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
  10. Press ENTER. You should see "SS" or "55" in the console.
  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Sep 22, 2013 | Reebok Treadmill T 3.2

1 Answer

When you turn on treadmill the incline goes all the way up and all the way down. Does nothing else.


First we need to do a calibration follow this procedure
Press the Stop and the Speed Up keys down while inserting the safety key.
Press the Stop key one time. The Time window should read EP:2P. Some newer models may also say FP, Pass, or the like. This means that it passes the EPROM test.
Press either incline key and the incline will calibrate automatically.
THIS IS A VERY IMPORTANT STEP BECAUSE YOU WILL GET AN ERROR MESSAGE IF THIS STEP IS SKIPPED. After completing calibration of incline, press the Stop key and then remove the safety key.
If the incline moves but you it will not operate normally nor calibrate, check the wiring from the incline sensor to the power board. If all looks normal, put it back in calibration and see if you see a blinking “- -” symbol in the incline window when you are calibrating. If not, the incline sensor is bad Call icon Fitness @ 800-999-3756, they may have the sensor or they tell you, you need to replace the incline motor

May 29, 2010 | Proform 675 E Treadmill

1 Answer

E02802


Hi, 1) Power off the Printer.
2) Press and hold the INFORMATION + STOP + OK buttons simultaneously, then press the POWER button. Release the buttons when the message "FIRMWARE UPDATE" appears in the display.

If Print Head is replaced without updating firmware, the machine will go into error. In order to bypass this error, CITS (800-423-2366), will ship the L-Printer Service tool CD upon request. This tool will override the error code and allow you to update firmware with the new Print Head.

Regards, polysandy

Apr 19, 2010 | Canon imagePROGRAF W6400 InkJet Printer

2 Answers

Image 17.0 Treadmill is stuck in incline position and will not go down. I do not plan to use the include at all, is there a manual way to move the incline to 0? Any suggestions?


Hello there, The first thing I would try is to calibrate the incline on the unit.
Do this using the following procedure.
With the safety key out, press the stop button along with the speed up button while inserting the safety key onto the unit.
remove your fingers from all buttons, Then press the stop button one time. Now press the incline up button one time.
The unit should go all the way to the top, then return to the bottom.
Remove the safety key and reinsert it to continue using the machine

If this does not work you can manually move the machine to the bottom using this procedure.
Remove the hood cover b removing 2 screws in the rear of the machine and removing the first 2 screws on the foot rails on each side.
You can now lift the cover out of the way.
At this point you will see the incline motor located in the center of the unit pointing in a downward direction.
On the top of the motor there will be a small fan encased inside of a metal cover. There will be a flat head screw located inside the metal frame where the fan is. Rotate this clockwise to lower the unit. (the motor is geared very high it may not seem as though it is moving but it is) be patient that procedure does take a little while.
Any questions please feel free to leave another message on this link.

Good Luck! Tim

Jan 10, 2010 | Icon Image 17.5 S Treadmill

1 Answer

Removed the sorter from a ricoh FT5832 copier and replaced with copy tray. how do I bypass the sorter cover (C-5) error message? Will not operate without the sorter plugged in.


Enter the SP mode by hitting the CLEAR MODE key, 1 0 7 then hold the CLEAR STOP key. When SP mode is selected , "1" blinks. Then enter SP 6-101-0 by hitting 6 then the . (dot) key, the 101 then the . (dot) key then the 0 key then the . (dot) key. This will tell the copier that NO sorter is intsalled. Hit the CLEAR MODE key 3 times or turn the machine off/on.

Sep 26, 2009 | Office Equipment & Supplies

1 Answer

Canon MP210 Third Party Ink Canon Does Not Work!


When the error message comes up, try pressing the "stop/reset" button and holding it down for at least 5 seconds. This works when I get an error message with compatible cartridges (only my error message says the ink is empty - and I know it isn't)

Jul 21, 2009 | Canon PIXMA MP210 Photo All-In-One Printer

2 Answers

Error # 09,035.43:10755


09,03x

35 = Cyan
36 = Magenta
37 = Yellow
38 = Black


The error indicates an ink stick was jammed. You have to clear the ISC (ink stick count) error.

Turn off the printer.
Turn on the printer.
As soon as you see XEROX start moving across the display hold down the back and help buttons until you see "beginning service mode" on the display.
Release the buttons, it will now come up in the service mode.
Scroll down to the function menu, hit ok, scoll to clear isc faault, hit ok.
Hit the back button to get back to the first menu then exit diagnostics, hit ok when it asks if you want to restart in customer mode.

May 12, 2009 | Xerox Phaser 8560DN Laser Printer

1 Answer

On bootup checks, stops at 02FC Main and second fans failed. Black screen with bootup messages. ?Has the MA7 even got two fans? How to correct.


Sounds like you may have a virus or trojan of some sort. They are hard to get rid of but try downloading avg 8.0 it's free and picks up most trojans and viruses. If you get a black screen with boot message just hit control alt delete together and your pc should bypass this problem and allow you in. If avg doesn't pick up trojan or virus it maybe a software failure but it will usually tell you whats missing and if pc was working fine and just started this it is most likely a virus or trojan

Jul 26, 2008 | Gateway Computers & Internet

1 Answer

IP4300 print error message


Try holding the "resume" button (triangle in circle) for about 10 seconds for each cartridge.
If that doesn't work, go to a refill shop and ask if they have a re-setter for your cartridges. Most shops do.
The re-setter gives new serial numbers to the cartridges, so the printer thinks you have put in new ones. Or you can buy one.
In 99%, when the printer tells you that one of the cartridges is empty, it's actually not. The chip is the one that tells the printer when to stop printing. If you bypass the chip, you can continue printing.
Hope that helps!

Sep 12, 2007 | Canon PIXMA iP4300 InkJet Photo Printer

Not finding what you are looking for?
Spirit Weslo FREE SPIRIT 815 Treadmill Walking Belt Logo

Related Topics:

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Spirit Exercise & Fitness Experts

MrJunk

Level 1 Expert

12 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Mister G
Mister G

Level 1 Expert

31 Answers

Are you a Spirit Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...