Question about Xact Communication EXG2801 Cordless Phone

1 Answer

Both handsets of the new 2801 we bought will not maintain charge

Only lasts 2 minutes before they start to beep and shortly after go "scratchy" and fade out.

indicator light on appears red when on the recharger base

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

This condition is usually caused by a battery that has been charged too much or incorrectly. It has developed a memory and now can only hold a very small charge. I believe it is time for new batteries!

Posted on Jan 22, 2014

6 Suggested Answers

SOURCE: handset wont register

Unplug the battery and try again. Worked for me.

Posted on Jun 17, 2007

  • 1 Answer

SOURCE: Handset No Link To Base error and no dial tone

I have the problem. I think it is because the battery i have in it was a Ni-MH and it should be a Ni-Cd. I am now looking for the right baterry Good luck Frank wolfgang24@verizon.net

Posted on Sep 17, 2007

  • 1 Answer

SOURCE: handset has No link to base

I was having the same problem with the same model phone, and fixed the problem by rebooting the phone – unplugging the AC and phone cord from the base station and plugging both back it, then removing and replacing the handset to regenerate the security code.

Posted on Nov 19, 2007

SOURCE: Handset ?No Link To Base? error and no dial tone

2/29 Have you registered or re-registered the handset?
"No link" can mean handset is not accepting radio wave of base unit. At Mfgr website pull-down operator's manual and look for registration instructions. Some sequence of buttons will create a radio signal from base (have handset off base) then another sequence of buttons on handset will accept radio signal. If handset has "menu" button, try "menu", then "00" (zero zero) then select an accept or "OK" button. Good luck.

Posted on Feb 29, 2008

  • 272 Answers

SOURCE: Unable to talk on two handsets at same time when receiving a call

Unfortunately that is the untold story about cordless phones they only have the capability of 1 open line be it the handset or or the base. There are some very pricey multi line systems, I have the same system bought two extra handsets and found out too late that I can only use them one at a time! Sorry probably not the answer you were looking for but thats the reality...

Posted on May 22, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to register my panasonic kx tga641es to the base. I have no instructions/user manual...can anyone help please???


I have similar model and setup should be the same..
1, Handset: press Menu
2, Handset: scroll using up/down arrow keys to "Initial setting" then press soft key Select
3, Handset: scroll to "Registration" press soft key Select
4, Handset: sroll to " HS Registration" press soft key Select
5, Base Unit: Press and hold (LOCATOR/INTERCOM/TRANSFER) for 3 seconds. The Charge indicator flashes. After the CHARGE indicator starts flashing, the rest of the procedure must be completed within 1 minute.
6, Handset: 1: press soft key OK
2: wait untill a long beep sounds and the display shows the new extention number
**Registration should be complete**

Aug 25, 2011 | Panasonic KX TGA641ES 1Line Cordless...

1 Answer

Hi, suddenly I loss my connection of telephone KX-TG 5632to the base from the handy , I need the way to register it from the base, thanks for your cooperation


1 Handset: {MENU} i {0}{0} 2 Base unit: Press and hold {LOCATOR/ INTERCOM} until the CHARGE indicator flashes. L After the CHARGE indicator starts flashing, the rest of the procedure must be completed within 1 minute. 3 Handset: Press {OK}, then wait until the handset beeps.

Jun 12, 2011 | Panasonic KX-TG5632 Phone

1 Answer

I purchased replacement handsets for my older panasonic cordless phone and would like to know how to reprogram them. My base unit has an answering machine but not a locater button. Thanks, Ann-Marie...


Follow these steps to register new handset.

1. On your Handset: Press Menu -> [0] [0] (menu then zero zero)
2. On your Base:
- Press and hold [Locator/Intercom] until the CHARGE indicator flashes.
The following must be completed within a minute.
3. On your Handset:
- Press [OK], then wait until the handset beeps.

That's it.

Hope this helps.

May 06, 2011 | Panasonic KX-TG5632 Phone

2 Answers

Phone displays a message saying no link to base when it is closer to the base?


Hi,

Following may be the cause for getting no link to the base.

1. The handset has lost communication with the base unit.Move closer to the base unit, and try again.

2. Confirm that the base unit’s AC adaptor is plugged in.

3. Raise the base unit antenna.

4The handset’s registration may have been cancelled .Re-register the handset.

To Register, follow the below steps.

Headset: Press MENU and then press ‘0’ ‘0’

Base unit: Press and hold HANDSET LOCATOR until the CHARGE indicator flashes.

(After the CHARGE indicator starts flashing, the rest of the procedure
must be completed within 1 minute.)

Handset: Press OK, and then wait until the handset beeps.

Your handset is registered to Base unit.

Thank You

Aug 18, 2010 | Panasonic KX-TG2620 Cordless Phone

1 Answer

Sync a new handset to kx-tg5632 phone


This works on MY panasonic; May work on yours too!

Registering a handset
The included handset and base unit are
preregistered. If for some reason the
handset is not registered to the base
unit, register the handset.
1 Handset:
{MENU} i {0}{0}{1}
2 Base unit:
Press and hold {LOCATOR/
INTERCOM} until the IN USE
indicator flashes.
LAfter the IN USE indicator starts
flashing, the rest of the procedure
must be completed within 1
minute.
3 Handset:
Press {OK}, then wait until a beep
sounds.
4 {OFF}
Registering an additional handset
See page 5 for information on the
available model.
Start from step 2.

Dec 29, 2008 | Panasonic KX-TG5632 Phone

2 Answers

Deregister lost or broken phones


Some tricks from a helpful Uniden rep:

holding down end+# keys at the same time on the phone for about 10 secs (you will hear a beep) will deregister the handset. If you have a dead handset and want to deregister it from the base, you have to reset the base. unplug the phoneline and power. hold down the "delete message" key, plug power back in. about 10 secs later, you will hear a long beep (theres a short beep upon powerup as well). At this point all handsets are deregistred and you will have to reregister them with the end+# trick. this way when #1 handset is dead, you can make a working one #1 and get the broken one fixed emotion-1.gif

BTW, this is a woot warranty, not uniden warranty. however the uniden rep gave me the number to the people who refurb (rox0rz!) these. I'll post an update when I finally get ahold of them (and the number if its actually helpful)

Jun 20, 2008 | Uniden TRU8885 Cordless Phone

1 Answer

Vtech 8L55 2 unit portable phone


I just had the same problem. Could be dirty terminals. I took the battery out, cleaned the terminals on the battery and phone with a pencil eraser, put the battery back in and it's working fine. (Says fully charged, where just a few minutes ago it said low battery).

Nov 06, 2007 | Vtech IP8100-2 Twin Cordless Phone

1 Answer

Phone loses connection after few minutes


I looked up the battery specs for your phone. They are 3 X 200mah= 600mah battery packs. They should last 8 hrs talk time with the headsets. This style of battery pack in my experience only last about 1 1/2years and sometimes longer and "sometimes" shorter...much shorter. I bet you never had problems when you first got them. Basicly this "battery design arrangment" goes back many years before newer battery technlogy was developed. But designers still insist on using them even today. They are cheap to make. ****Time to replace them with new ones.**** Make sure you follow the mfgs charging instructions: "After battery installation, place the handsets in their base unit or charger and allow to charge for 16 hours before use. You can keep the battery charged by returning the handsets to their base unit or charger after each use. When the battery is fully depleted, a recharge takes about 12 hours. Average talk time on a fully charged battery is about eight hours depending on environmental conditions, standby time is approximately four days." Good luck

Jul 19, 2007 | AT&T E5640 Phone

2 Answers

Handset No Link To Base error and no dial tone


I have the problem. I think it is because the battery i have in it was a Ni-MH and it should be a Ni-Cd. I am now looking for the right baterry Good luck Frank wolfgang24@verizon.net

Jan 27, 2007 | GE 900 MHz Phone

Not finding what you are looking for?
Xact Communication EXG2801 Cordless Phone Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xact Communication Lands Phones Experts

kakima

Level 3 Expert

98608 Answers

Cindy Wells

Level 3 Expert

4798 Answers

yadayada
yadayada

Level 3 Expert

63242 Answers

Are you a Xact Communication Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...