Question about Danby DPAC10061 Air Conditioner

1 Answer

I have pluged in the air conditioner but nothing happens

The face plate lights up and i can set on off times and wohat not but notheing happens no fan or ac turns on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 577 Answers

Did you set your thermosstat temperatures, they have to be lower than the actual room temperature at the time for cooling.

Posted on Mar 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I turn on my unit the cooling light flashes but nothing happens


Your unit may have a wall control which can set the Evap cooler to a pre fill mode time which fills the base with water then there is a pre wet mode which starts the pump to wet the pads. After both these functions have completed the fan will start. This could take up to 4 minutes before the fan starts and can be programmed out if not required.

Nov 25, 2014 | Air Conditioners

1 Answer

Repaced fan motor, capacitor, contactor still fan not working.


press the contactor in using a wooden pencil does it come on? if so then you are not getting a control signal from the tstat or a low pressure (low freon switch) is open stopping the contactor from pulling in

May 21, 2013 | Goodman CKL49AR49 Air Conditioner

1 Answer

If you turn the controller to heat nothing happens. If you turn the controller to fan then the fan turns on - then if you choose heat the fan turns off after a few seconds. Is there a pilot light that has...


most systems are on a time delay, try turning it to heat and waiting a few minutes. if that dosent work see if your emergency heat works(there should be a setting for that on the thermostat)

May 04, 2011 | Air Conditioners

1 Answer

My remote control will not turn on. The timer function comes on but nothing happens. model GZ-1002B-E3 mistral MSS2.6


take your chellphone and open the camera,then take the control and push any button in front of the chellphone.if the remote is ok you see a light blinking.if you didnt see the light the eye of the small plate have the problem.

Dec 09, 2009 | Hitachi RAS-09UH Air Conditioner

1 Answer

I have a programmable thermostat. The LED reads Replace batteries. The face plate has fan switch, a system switch, two arrow keys that are separated by three little function (set, hold, and run). HELP!!...


There is a base plate that is screwed to the wall. The face of the thermostat should come off from the base. Usually the batteries can be found back there. Some times a little tug will get it off the wall. Other models have small plastic release clasps that when pushed in will allow the unit to come off.

Jun 30, 2008 | Honeywell Air Conditioners

1 Answer

No Air


30 is too low. Raise the thermosta to 74 and see what happens

Jun 04, 2008 | GE Built-In Room Air Heat Cool Air...

Not finding what you are looking for?
Air Conditioners Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Danby Air Conditioners Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

CheckitRight
CheckitRight

Level 3 Expert

1349 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you a Danby Air Conditioner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...