Question about Onkyo TX-SR605 Receiver

2 Answers

I recently bought TX-SR605 7.1 receiver it was working fine but lately whenever i switch the on button it comes back immediately to the standby mode, can somebody help me out

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 98 Answers

Its possible that the Receiver is going into protection mode and possible some speaker cable might have touched the body or with each other.
Remove all inputs and outputs and then restart the receiver. If it starts then you are lucky. Connect all cable and wiring properly and ensure that they do not touch each other. You might have to reset the microprocessor if the recevier has got.

If the problem persist then let me know to further the trobleshooting.

Please do rate this solution and thanks for using FixYa.

Posted on Mar 04, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I don't really have a solution, but my 605 sometimes does this same thing when using the remote. Try actually touching the on-off button on the receiver itself rather than the remote. This works for me everytime.

Posted on Apr 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TX-SR333 Bluetooth worked the 1st time now won't pair up.


Hi, Please try the following reset and then try to pair again.

To do the reset you need to turn the receiver on, then on the front panel of the receiver press and hold the "CBL/SAT" button while doing that press the "STANDBY/ON" button. You will see the word "Clear" in the display screen and the receiver will go into standby mode. PLEASE UNDERSTAND THAT YOU WILL LOSE ALL YOUR AUDIO & VIDEO ASSIGNMENTS ON THE RECEIVER PLUS YOU WILL LOSE ALL YOUR SPEAKER CONFIGURATIONS, SPEAKER DISTANCE AND ALL LEVEL CALIBRATION SETTINGS. YOU WILL ALSO LOSE ANY PROGRAMMED RADIO STATIONS IN MEMORY. Once the receiver goes into standby mode turn it back on and go thru the setup menu for all custom settings, Thanks, JT

Feb 27, 2015 | Onkyo TX-SR333 5.1-Channel Home Theater...

1 Answer

Onkyo TX NR515 .. when in standby mode .. light is not coming on .. everything works fine .. i must have pressed something by mistake but cant work it out what ... on the display panel in standby mode...


If Zones are turned on or, if a mobile device connected to the Front Input is charging (MHL), the HYBRID STANDBY indicator won't light. See the TX NR515 owner's manual at http://filedepot.onkyousa.com/Files/own_manuals/TX-NR515_English.pdf for more info.

Feb 19, 2015 | Onkyo TX-NR515 AV Receiver

1 Answer

Receiver standby sound


If the receiver goes into protect mode with no speakers connected, you will have to troubleshoot the receiver itself to find and correct the problem.

Mar 07, 2014 | Onkyo Audio & Video Receivers

1 Answer

Receiver stays on stand by


Turning On and Standby
On the AV receiver, press the [ON/STANDBY] button.
On the remote controller, press the [RECEIVER] button, followed by the
[ON/STANDBY] button.
The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
To turn the AV receiver off, press the [ON/STANDBY] button, or press the remote
controller's [ON/STANDBY] button. The AV receiver will enter Standby mode.

If you have any trouble using the receiver, a simple reset could solve your problem.Note that resetting the AV receiver will delete your radio presets and custom settings.
To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [ON/STANDBY] button. "Clear" will appear on the display and the AV receiver will enter Standby mode.

tinualbinale_5.png
Hope you are satisfied with my solution.Your valuable feedback would be appreciated.Thanks for choosing Fixya.

TinuAlbinAlex

Jun 15, 2011 | Onkyo TX-SR307 A/V Receiver

1 Answer

Trips and switches off


Hello Fixya customer,

Thank you for your question.

The best way to fully isolate the fault is to disconnect all the speaker wires, and verify that there are no strands of wire shorting between the speaker terminals on the rear of the unit.

Turn the volume all the way down, full CCW, and if it goes into shut down with the STBY light blinking then there is a fault in one of the amplifier's.

Thank you for using Fixya, and if I can be of further assistance please ask.

May 01, 2010 | Onkyo TX-SR706 Receiver

1 Answer

My reciver just shutdown then went into standby mode. Will not power back on. How do I fix this problem?


What do you mean by standby mode? Do you hear the power relay switch clicking constantly, or does it just click once and turn off? In any case, it could be a faulty power relay. I just sent in my TX-SR806 for warranty repair recently, and it ended up being just that.

Nov 13, 2009 | Onkyo TX-SR806 Receiver

1 Answer

My rxv 1800 wasnt used for probably a year but was left plugged to a wall outlet during that time it wasnt used. when i came home last week, i switched it on but immediately shuts off after a second. when...


r this one: Switc off your receiver using the main power button on the front face. Hold the the Effect button and the Direct button, and turn the main power ON.f it ain't working, try this one: Turn your receiver ON and, while holding down the [VCR1] button, press the [STANDBY/ON] button. "Clear" might appears on the display and your receiver might enter Standby mode.
Hope it does.. With your receiver in the Standby mode, hold on STRAIGHT (EFFECT) on the front panel and press STANDBY/ON.
* The ADVANCED sETUP menu appears in the front panel display.ress STRAIGHT (EFFECT) to select the desired setting.
RESET = To reset your receiver to its factory presets.
CANCEL = To cancel without making any changes Press STANDBY/ON to confirm your selection.
* If you selected "RESET", your receiver is reset to its factory presets and switches to Standby mode good luck

shaun

Aug 24, 2009 | Yamaha RX-V1800

1 Answer

Onkyo TX-SR605 - Suddenly switches itself off and back on


HI, this is a reset procedure that this unit is trying to initiate. there has been a surge of some sort that the system has survived but, there is some lasting damage as well that has resulted in a slight programming error within the mother board.

This unit has a program that was installed at the manufacture. it runs the basic operations. there has been some major damage that is causing the internal program to stall and reset itself. the only way to reprogram is to send it back to the manufacture or, you can locate a local repair depot through Onkyo. the Onkyo techs are the only option when re programing is needed.

May 13, 2009 | Onkyo TX-SR605 Receiver

1 Answer

Onkyo TX-DX838


I went back and found a loose cable/coax. Re-attached and now the receiver works as good as ever.

Sep 02, 2008 | Onkyo TX-DS838 Receiver

1 Answer

No Power


I mwas gonna suggest that you need the speakers attached but you stated later that it did the same thing with the speakers attached. The unit switching off after it checks its self is NOT a normal thing. TAKE IT BACK BEFORE ITS TOO LATE!! GOOD lUCK

Jun 18, 2006 | Denon AVR-1706 Receiver

Not finding what you are looking for?
Onkyo TX-SR605 Receiver Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio & Video Receivers Experts

D. E. Hev

Level 3 Expert

1059 Answers

gbob59

Level 3 Expert

2963 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Are you an Onkyo Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...