Question about NetGear WGR614 Wireless Router

2 Answers

Can't login with password

My netgear router WGR614v7 says that I can't login because "this network is being run by admin: 192.168.1.5" and it won't let me login just because I'm not on the computer that is 192.168.1.5 I'll let you in I can figure it out. please help if you think of something!

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 67 Answers

Perhaps someone has hijacked your router. It is possible if you never changed the default login information for your router and it was unsecured. If there's a reset button on the router, try to press it for 15 seconds to reset the router to default settings. It might be a small depressed hole in the bottom/back of the router that you have to push with a pen or opened paper-clip.

Once it's reset, do the following:

  1. Open your web browser
  2. Enter "192.168.0.1" (without quotes) in the address bar
  3. When prompted for the password, you're either going to enter "admin" for a username (without the quotes) and "password" as the password (without quotes), or "admin" (without quotes) and the password of "1234" (without quotes).
  4. Once in, navigate to some type of administration options and change the username/password for your router. Be sure to write them down so you don't forget.

Posted on Mar 04, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 121 Answers

HI,

Configure your IP address to static 192.168.1.5 and try logging in. As long as the computer isn't running with that IP you should be able to access it. The other option is to reset the router and configure it to allow access from any computer.

Armymason

Posted on Mar 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Default network password


for NETGEAR the login password for connecting to the network should be printed on a label on the router itself. If you are looking for the password to login to the router for configuration... login is "admin" password is "password" (without the quotes)

Jan 11, 2014 | Computers & Internet

1 Answer

What is the code for netgear WGR614v7 to enter to a laptop for wireless wifi?


Connect a LAN cable from the Netgear to the LAN port on your computer, open a browser and enter the Netgear configuration URL -
http://192.168.0.1
The default login = admin
The default PW = password You can now change the default admin password and configure the wireless settings.
Go to the wireless configuration and set up the SSID and WPA or WPA2 encryption to protect your wireless network and Internet from unauthorized access.
Now apply these settings to the wireless card in your laptop/computer.
To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security b>

Jan 28, 2013 | NetGear WGR614 Wireless Router

1 Answer

HP Touchpad won't connect to Netgear MNR2000v2 wireless router


To RESET the Netgear, power up the Netgear then press andhold the RESET button at the back of the router until all the LEDs flash.Connect a LAN cable from the Netgear to the LAN port on yourcomputer, open a browser and enter the Netgear configuration URL -
http://192.168.0.1
The default login = admin
The default PW = passwordYou can now change the default admin password and configurethe wireless settings.
Go to the wireless configuration and set up the SSID and WPA or WPA2encryption.
Now apply these settings to the wireless card in your laptop/computer.
To secure your wireless network from unauthorized access, please click on thislink and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

Jun 30, 2012 | NetGear Computers & Internet

1 Answer

Open basic settings page for 192.168.1.1


once there you need to type username admin and password is password if you cannot do it ,you may have to do:
reset to factory default

press and hold reset button during the whole process and only release when completed.

1)press reset button 30 seconds
2)remove power cable 30 sec
3)plug in power cable 30 sec and then release.

You should no be set for 192.168.1.1
username admin
password is password

Dec 30, 2011 | NetGear WGR614 Wireless Router

1 Answer

Forgot username & password for netrouter wgr614v7


How do I log into my router?
To log into a NETGEAR router:
  1. In your Web browser, navigate to the router login page. By default, one or all of the following URLs should work:
    • http://www.routerlogin.net or http://www.routerlogin.com
    • http://192.168.1.1 or http://192.168.0.1
    Note: You can sometimes find the login URL on a sticker on the bottom or back of the router.

  2. Enter the username (admin) and the password.
    • The default password is password, or for older routers, 1234.
    • If you have already changed the default password, use the password you assigned the router. Passwords are case sensitive.
    • If you have already changed the password and do not remember it, you have to reset the router to factory defaults in order to use the default password. Resetting a router to factory defaults erases all changes you have made to the router's configuration files.
This information is extracted from www.netgear.com, for learning purpose only.

Hope this will be useful for your question.

Good luck. Remember to rate my answer please.

Jul 13, 2011 | Computers & Internet

1 Answer

Our netgear wgr614v7 54 mbps wireless router has gone bad acording to our net work service.They tested there modem,that had astrong signal.now here is whats happnen,there is no signal frm modem to wireless...


This guide gives you the directions for setting up wireless on the Netgear WGR614v7.

Basically enter the routers ip address (192.168.1.1) in your browser. If you router has default configurations, then enter the username as "admin" and the password as "password." Navigate to "wireless settings" and then on that page you configure your network.

Jun 13, 2011 | NetGear WGR614 54 Mbps Wireless Router -...

3 Answers

I need to reset or find my origional password. Please help. Thanks


If you have changed the default password, you need to reset the router to the factory settings to get in with the default user and password (user admin and password as password, or if that doesn't work try 1234 - these are the default password for NetGear routers). Note that you will lose the ISP settings and wireless settings when you reset the router.

Here's a video on how to reset the router to the factory default settings: http://kbserver.netgear.com/media/flash/training/Troubleshooting/NG_WGR614V9Router_TS_LostPassword.html

Feb 17, 2011 | NetGear DG834G Router

1 Answer

Trying to reconfigure my netgear router


First Press RESET button for 10 seconds it is in back panel of router.
Then connect router to computer with ethernet cable.
Then you can access it with following link.
http://192.168.1.1
or
http://192.168.0.1
type user as "admin" and password as "admin" or blank or "password"
then you can see configuration page of router.
Let me know if you need further assistance.
Thanks for using FixYa.

Dec 02, 2009 | NetGear RP614 Router

1 Answer

Network key


If you forgot your admin password too, it's gonna be tough.

On a computer connected to the network go to www.routerlogin.com the usnername is always admin and the default password is password. If that gets you in, you should have no trouble finding the networking key under wireless settings.

If you don't know the login password, you may have to reset the router.

Carl

Jan 14, 2009 | NetGear WGR614 Wireless Router

Not finding what you are looking for?
NetGear WGR614 Wireless Router Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...