Question about GE 24 in. GSD2220Z Built-in Dishwasher

1 Answer

Standing water washer not draining completly after wash is finished

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I would say you have a clogged drain hose. Check the hose for any blockage. Also may need to check under the dishwasher where the drain hose connects to the washer - this is where i've had blockage before. Make sure the power is off to the machine, as the wiring is around that area also.

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dishwasher not draining


It has a drain line that goes to a fitting on the garbage disposal or the sink drain if no disposal. It is held on with a hose clamp and can clog easily

Apr 06, 2014 | Frigidaire 18" Built-In Dishwasher

1 Answer

Dishwasher won't drain completely. Several inches of standing water left after last cycle


Sounds like the wash/drain selector valve might be stuck. my Kenmore operating solenoid rusted and hung up. I cleaned and oiled it up. You can also have something that got into the valve and it won't close, or an obstruction in the drain hose or the drain pipe connector. Something is restricting the flow or the pump itself may have a bad impeller. Does it wash with vigor or has it lost a little oomph and sound different? Does it leave any debris on the dishes?

Jan 25, 2012 | Dishwashers

1 Answer

The G638 finished its cycle but didn't completely


pump maybe on it's way out, though i doubt it, is the washing machine on the same drain out? if so you may have back wash, another could be lengh of drain hose, i had the same problem with my miele dishwasher because of the position in the kitchen i doubled up the drain hose and though it pumped out fine, with the volume of water left in the hose it came back in untill i repositioned the drain hose so it could't run back, hope this helps.

Aug 03, 2009 | Miele 24 in. G638 Plus Free-standing...

1 Answer

Dirty water is standing in the bottom of washer when finished what to do?


Check the drain for clogs and also the drain screen. Flush washer with new water. You can use a bucket of water and the drain cycle

Jul 29, 2009 | Dishwashers

1 Answer

Soapy water standing in bottom not rinsing soap off dishes


It sounds as if it is not draining. Try to trace the drain line under the sink. Usually it goes into a disposall. The port where it connects to the disposall may be clogged. Another thought. If you had the disposall replaced recently they may not have taken the knock out plug out which would give the drain water no where to go.

Apr 09, 2009 | GE Tritonr XL GSD6260JCC Dishwasher

1 Answer

Water in the bottom of dishwasher


try running it empty there is usually a drain hole in the bottom check if anything is in it or try a dish washer wash solution I bet the drain or drain line is cloged let me know if this dont work. Hows your sink draining

Feb 15, 2009 | Kenmore 17459 Free-standing Dishwasher

1 Answer

Water left after finishing wash


I have a Bosch Dishwasher and the E-Nr is SGS4362EU/03. The machine is approximately 4 years old, in good condition and has been working very well. Suddenly, there is water remaining after it completes a 50 degrees C wash cycle. This is also evident with the pre wash cycle and the 65 degrees wash cycle.

I have checked and cleaned the filters. I have loosened the internal pump white cover (Torx T 20 screw) and checked for any physical blockage - none. I have also checked for any drainage hose kinks - none.

I have tried a series of empty washes and the machine drains the water during the wash cycles. The dishes are also have a dull colour and show show signs of not being properly rinsed during the wash cycle.

Please assist.

Reagrds,

Brian

Dec 27, 2008 | Bosch 24 in. SHY56A05 Stainless Steel...

1 Answer

LTF2140E Front loader washer


My Frigidaire front loader washer model LTF2140E doesnt want to drain the water when set to wash (heavy-normal-quick selectors). It washes put thats it. I have to switch the selector to drain/spin then rinse/spin cycle to finish the load. I checked the drain hose for any clogs....everything is clear. Any suggestions? Also,iIs2.gif their any reset buttons for this type of washer?

Dec 13, 2007 | Frigidaire 24 in. FDB510LC Free-standing...

3 Answers

Kitchenaid dishwasher - water standing at end of cycle


less than 2 cups of water in left after cycle complete

Dec 02, 2007 | Siemens 24 in. SE25A266 ExtraKlasse...

2 Answers

Whirlpool dishwasher


I had the exact same problem with my Whirlpool Quiet Partner IV. I removed the lower arm, and a couple of components below that, and got to the filter/grinder (that thing that chops up and filters the recirculated water before it goes to the pump that feeds the arms). The filter was completely clogged. I used a knife to scrap away the foodstuffs, put everything back together and all worked excellent. Just goes to show you that you should rinse your plates before to place them in the dishwasher.

Mar 14, 2007 | Whirlpool 24 in. DP840SWP Free-standing...

Not finding what you are looking for?
GE 24 in. GSD2220Z Built-in Dishwasher Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...