Question about Virtual Reality Sound VR3 CD Player w/ USB and Scan Disk Inputs

2 Answers

VR3 640g roadmaster won't "power on".

I am installing in a base-model 2007 Dodge Caliber SE. I connected all the radio wires. I connected the red / black / yellow wires to the corresponding ones on the harness.

The unit has power as the face opens and closes. However, i can't get it to power on. Does the brown wire need to be connected first? is the thing broken?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What u need to do is get a different wiring harness for it, i had the same problem the harness comes with a gray power block on it

Posted on May 23, 2009

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 33 Answers

Sounds like it is broken. If you have the power wire hooked up as you said it should be working fine. Not sure which browm wire you are referring to but it should work regardless of that.

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can i install an pioneer cd player in my 2008 dodge caliber by cutting factory plug and connecting wires to wires if so how can i do this


Crutchfield is a great place to start with car audio install. Even if you don't use their products, the info is very useful:
Find what fits your car Crutchfield

Here is a video

Jan 02, 2015 | Car Audio Receivers

1 Answer

No sound from new install Pioneer DEH-X6600BT


You may be using the wrong adapter. Your Durango has a DK GRN/RED wire that supplies power to the separate amplifier. Your adapter may not have provisions for connecting the steering wheel controls to your new radio. Also check 15A FUSE 4 in the junction block in case it is open.

Dec 29, 2013 | Pioneer Deh-X6600bt Car Cd Receiver...

2 Answers

Pioneer DEH-3300 UB


Apparently, you have no power at the 12 volt battery/memory wire at the radio harness of the vehicle. This wire is white with blue in color.
Also, based upon your description, you have connected the battery/memory wire and the accessory wire of the radio to the 12 volt accessory (switched) wire of the vehicle. This wire is white with red in color.
Check the radio/ stereo fuse of the car. You may have blown the fuse during your installation.
You have no memory at the radio because when you turn off the key, you lose all power to the radio.
Also, I mentioned the wire colors just in case you used an aftermarket radio wiring harness. Make sure that the yellow from the Pioneer unit is going to the battery power source and, the red of the Pioneer is going to the switched power source.

Sep 12, 2012 | Pioneer Car Audio Receivers

2 Answers

Installed Pioneer DEH-1200MP, won't turn on.


sounds like yours acc (red wire) is not connected

Aug 23, 2011 | Pioneer Deh-1200mp Car CD/ MP3 Player

1 Answer

I am installing the DEH-3200 into an 06 dodge ram. I bought a scorsche adapter kit and I followed all the instructions, but I can't get any power to the stereo? Any suggestions?


if you have a digital volt meter check powers at radio to see if your getting a good ground ..

take the black test lead of the meter put it on the ground were you mounted ground wire. then take the positve red test lead and the touch the red wire on harness from radio to see if there is 12 volts

and the do the same for the yellow wire constant power must have 12 volts all so if you get nothing either its a bad ground or fuse is blow then check fuses if everything is good and no fuses or blow then the radio is bad ....

Dec 22, 2010 | Pioneer DEH3200UB w USB Input iPod...

1 Answer

I need the wiring diagram to install a Alpine 7516 in a Dodge Colt 1994.Thanks! Alain


1994 Dodge Colt Car Audio Wiring Guide


Car Radio Battery Constant 12v+ Wire: Blue/Red
Car Radio Accessory Switched 12v+ Wire: Blue/White
Car Radio Ground Wire: Chassis
Car Radio Illumination Wire: N/A
Car Stereo Dimmer Wire: Red/Black
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: 4′
Car Audio Front Speakers Location: Dash
Left Front Speaker Positive Wire (+): Blue
Left Front Speaker Negative Wire (-): Blue/White
Right Front Speaker Positive Wire (+): Blue/Red
Right Front Speaker Negative Wire (-): Blue/Yellow
Car Audio Rear Speakers Size: 6 1/2′
Car Audio Rear Speakers Location: Rear Deck
Left Rear Speaker Positive Wire (+): Blue/White
Left Rear Speaker Negative Wire (-): Blue/Green
Right Rear Speaker Positive Wire (+): Blue/Red
Right Rear Speaker Negative Wire (-): Blue/Green


The manual for the Alpine 7516 can be purchased here:
https://www.samswebsite.com/en/photofact/search/index/model/7516

Jul 19, 2010 | Alpine Car Audio Receivers

1 Answer

How to install an aftermarket radio in a 2004 Chevy C2500


You will need a wiring harness for the model truck you have, plus a filler kit. The filler kit is what the radio will actually attach to and fill the space left by the factory radio. Follow the diagrams for wiring from the harness and the aftermarket radio. Generally, there are 8 wires to be connected for a four speaker system. In addition, you will connect a ground wire (black), a yellow wire (constant power), a red wire (this is to turn the radio on and off with the ignition), and a solid orange wire (illumination). Because you have a GM product you will also need an antenna adapter. All these things can be purchased at Best Buy, or WalMart.

Apr 22, 2010 | Kenwood Car Audio Receivers

2 Answers

I install a radio it dont keep a memory


Pull the radio back out. I bet you hooked up both power wires (red and orange or yellow) to the ignition on hot wire. Orange or yellow depending on the radio usualy goes to the ignition on hot wire and red to a constant hot wire. Check the radio wiring diagram or list. One of the power wires has to go to a full time power source. check the wires with a circuit tester with the key off till you find the constant hot wire (battery power)

Dec 17, 2009 | Kenwood KDC-MP228 CD Player

Not finding what you are looking for?
Car Audio Receivers Logo

435 people viewed this question

Ask a Question

Usually answered in minutes!

Top Virtual Reality Car Audio Receivers Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

kakima

Level 3 Expert

96417 Answers

Tom Chichester

Level 3 Expert

24447 Answers

Are you a Virtual Reality Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...