Question about Cyberhome CH-DVD 300 DVD Player

2 Answers

Cyberhome player will not turn on--

I cannot make the player come on. I have used the remote and the buttons on the Cyberhome but nothing happens. The.re is a CD in it placed in it about three weeks ago

Posted by on

  • Anonymous Apr 01, 2009

    dvd player wont turn on

  • Owings Mills Apr 08, 2009

    The cyberhome player will not trun on. It was working fine from the last time I used it. I disconnected it and put it away form some time and when I reconnected it, it would not turn on. Please advise.



    Thanks

    User

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I had the same problem, only the LED stayed light red/orange and nothing worked. With the unit unplugged, first try to manually eject the DVD by sliding the plastic tab in the slot on the bottom in the direction indicated by the arrow. Leave the tray extended and plug back in. Or, with the unit unplugged, press and hold the Eject button and then plug back in. If none of those work and the fuse is good, check this site: http://www.drx9000repair.netfirms.com/#Cyberhome%20CH%20300
Mine had a low 5V supply. I did the change to the PC board as shown on this site and added a ~90K resistor from ZD2 to U3 and viola it fixed the problem!!

Posted on Mar 07, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Are you sure it is plugged to the mains?
Check the power cables to see if it has some cracks/bends.
if the above is incorrect - it might be that the internal fuse is blown - this needs a lab/technician to be fixed.

Posted on Mar 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Cyberhome CH DVD 300 (region 1), I want to change the region on this player. I learned I need for first: 1.- Turn On the DVD player 2.- The tray needs to be closed and empty 3.- Press the Menu...


  1. Turn on the player (without a disc inserted)
  2. Close the disc tray
  3. Press MENU, 1, 9
  4. Selection menu will be displayed
  5. Press ENTER
  6. Select region
  7. Press ENTER
  8. Press OPEN/CLOSE

Dec 07, 2010 | Cyberhome CH-DVD 300 DVD Player

Tip

Cyberhome AD-N212 Region Free Fix Would you like to unlock your Cyberhome...


Cyberhome AD-N212 Region Free Fix

efc99c7.jpg
Would you like to unlock your Cyberhome AD-N212 DVD player to Region Free?

Follow these steps to unlock your Cyberhome AD-N212 DVD player:

  1. Open the drive tray
  2. Press the 7 button on your remote control
  3. Press the 6 button on your remote control
  4. Press the SEL button on your remote control
  5. You will now enter the hidden setup page
  6. Change the player toany Region or set it to Region Free by entering 13 as the country code.


Your Cyberhome AD-N212 DVD player is now Region Free.

I hope that helps.

on Apr 25, 2010 | DVD & Blu-Ray Players

1 Answer

Can't get my CyberHome CH-DVD 300 working


Check for bad capacitors on the alimentation fead target

Sep 01, 2009 | Cyberhome CH-DVD 300 DVD Player

1 Answer

Stuck on cyberhome screen


Sounds crazy but have you checked the battries in your remote , sometimes low battries will cause corruption in the internal processor chip and all that is required to sort it out is a new set .. try this if just replacing the battries and turning the set back on by the remote has no effect .. check the back of the set to see if it has a reset button some do other than that a local service engineer may be able to update the software on your machine for a small fee or at least be able to give you a free estimate on its repair .hope this helps .. regards Vortash

May 12, 2009 | Cyberhome CH-DVD 300 DVD Player

2 Answers

Remote Codes


I found the code...

In the remote codes guide, the Cyberhome DVD player is listed under "Portable DVD"...the code is 2083...worked for me, enjoy.

Dec 28, 2007 | Cyberhome CH-DVD 300 DVD Player

5 Answers

Need remote codes


I have a CyberHome CH-DVD-300 unit with a Dishnet remote. The remote code that worked for me is 724.

Sep 24, 2007 | Cyberhome CH-DVD 300 DVD Player

3 Answers

Cyberhome 300 DVD Player: pal to ntsc mode?


You might want to reset to factory defaults, but there is an error in the manual. In order to reset to factory defaults, turn on (with no disc inside), DO NOT OPEN THE DISC TRAY, just press the stop button on the player for 5 seconds.

Aug 02, 2007 | Cyberhome CH-DVD 300 DVD Player

2 Answers

Remote Control?


first un-plug the unit for about 1/2 an hour it should default to english

Mar 12, 2007 | Cyberhome CH-DVD 300 DVD Player

Not finding what you are looking for?
Cyberhome CH-DVD 300 DVD Player Logo

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cyberhome DVD & Blu-Ray Players Experts

zappal

Level 1 Expert

48 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Are you a Cyberhome DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...