Question about Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50 969 Oyster Bath Undermount, Righ

1 Answer

Whirlpool jacuzzi jets not working properly - Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50 969 Oyster Bath Undermount, Righ

Posted by on

  • flennie Mar 04, 2009

    Again - whirlpoo jacuzzu, but with one jet not working. Rest seem fine.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Im not a great expert in this field but try putting some dish washer tablets in water when running to see if they can clean out anything,about 3/4 tabs

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tub does not want to stay running when i press the button, you have to hold the button down for it to work


the buttons on most of the tubes are pressurized air when u push it sounds like a bad button or hose it could even be the little air sylenoid that clicks on and of when the air is forced against it when u press the button 1st check the hoses for leaks 2nd remove hose and verify the button works

Jan 14, 2011 | Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50...

1 Answer

Stop 2min and run for 2min, stop 2min and run for


your motor thermal safety relay is protecting the motor from burning out
this is usually caused by: an old motor about to fail (tight shaft bearings) bad centrifical switch or, an obstruction in the water flow causing the motor to work too hard (draw too many amps, get too hot then cool down and, start up again
check the relay it is located on the side of the motor on most motors; under a cover; unless the motor is bad the relay may just be too sensitive (old) and, may need to be replaced.

Jul 24, 2010 | Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50...

1 Answer

How to wire a jacuzzi whirlpool tub? What to use for wiring, timer etc?


get an electrician. you need to follow the code for the size of wire to use based on number of amps of the motor and how far away the pump is from the power outlet.

Sep 29, 2009 | Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50...

1 Answer

Hello, how I remove the water from my whirlpool jacuzzi bath Balboa Z112 spa so I can clean it


hook up a garden hose to a faucet. Put the other end in your spa. Then turn on the faucetuntil water comes out the spa end of hose. Make sure the end in the spa is weighted down so it doesn't come out. Then remove the hose from the faucet and keeping it lower than the spa lay the hose where it can drain with causing problems. The water will flow on its own draining the spa. You may want to clean it while its draing so the dirty water will be diluted and drain at thhe same time. Make sure the water is not drained out around any electrical AND!!! NO DIVING!!!! If you lose the prime, just fill the hose again with the faucet. Good luck

Jun 12, 2009 | Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50...

1 Answer

My Jacuzzi won't turn off or heat


The heater will only fire if it has water in it. If you just got the house, make sure the gas/electric to the heater is on. Turn off the pump and turn it back on.. See if that works. good luck

Jun 05, 2009 | Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50...

1 Answer

The Jacuzzi isnt recieving power


yes it could, it might even be the motor, take the electric suply and unplug it see if you can turn the shaft on the motor if not it froze up,, sometimes the get wet and seize, the you have to get a new motor

Feb 27, 2009 | Jacuzzi Allusion 7242 RH Whirlpool HTR...

1 Answer

Black soot in my jacuzzi tub


sounds like the rubber seals are going bad, does it recomend to run cascade thru the jets? this might be harmful to the gaskets and the pump, you maight want to disconnect the hose and flush out the tubes going around the tub, but I would call jacuzzi and ask them if this is good to run thru there, thye might be able to help you with the gaskets, questions over the phone do not cost you, call them, ask for repairs section good luck

Feb 27, 2009 | Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50...

1 Answer

No water hot


does it have a heater in the circulation line, it should be under the cover and would be in line on the 2 inch pipe that feeds the jets, it should also be on a gfci, check to make sure it is plugged in if this is plugged in and not tripped you need to install a new heater

Dec 06, 2008 | Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50...

Not finding what you are looking for?
Whirlpool Jacuzzi Jacuzzi Bath Fuzion EF50 969 Oyster  Bath Undermount, Righ Logo

Related Topics:

1,339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Water Heaters Experts

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

1869 Answers

80stech

Level 2 Expert

92 Answers

Mike

Level 3 Expert

4331 Answers

Are you a Whirlpool Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...