Question about Brother Printers & Copiers

1 Answer

No power to top of DCP9040N

Can anyone tell me what is wrong with my printer, as the top half has no powe to it hence the LCD display not lighting up.

However when sending a document from my PC the printer works well.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 62 Answers

The LCD may have gone out. The only fix is to replace the LCD screen which would be done by a local dealer. Hope this helped!

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon MP700 Multifunction printer displays message "Wrong cartridge"


1. With the printer powered off but connected to a power source, press the Power button while

pressing and holding the Stop/ Reset button.
2. When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4. When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in. (orange and green, starting with orange.)

Mar 24, 2012 | Canon MultiPASS MP700 All-In-One InkJet...

2 Answers

Alarm light blinking. wrong cartridge in LCD window.


remove the new cartridge and clean contacts of cartridge and iside printer with Qtips / alcohol..you might have communication problem with cartridge due to dirty contacts..sometimes they get dirty fro spilled ink from jets..then retry

Dec 17, 2007 | Printers & Copiers

1 Answer

I want to resolve error 5100 in canon mp 250 series printer pl tell me to do what


Error 5100 show your ink absorver almost full. So reset your printer by using the following methods. * Keep your printer off. * Now press stop/reset button and press power button with holding stop/reset button. * After your power is display a light release stop/reset button but still pressing power button. * Press Stop/reset button two times by holding power button. * Now release both button. * Wait for few minutes until your printer display "0" on your printer LCD. * Now download Canon MP258 reseter ServiceTool_V1050. After
pheireith244.jpg

Aug 11, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

HP 4100TN printer displays output bin full. The printer will not print.


Hi Bob

Thanks for posting

This is a simple problem bob. You can check if the paper exit path on top of the printer. You will find a small plastic flag which has got stuck and needs to be released hence you need to move it with your finger a little and this will go back to its original place normally and this will solve the problem.

This is the sensor responsible in telling the printer that there are lot of papers on top of the printer and no more papers can be dispensed out of the printer.

Jul 14, 2011 | HP LaserJet 4100 Printer

1 Answer

When power is on lcd display say call for servicing


tell me the error code at the right top on lcd display

Jun 18, 2011 | Toshiba e-STUDIO 352 Black and White...

1 Answer

Prints only top half of photos on top half of


I suggest that you go into the printer properties section on control panel. There Will be a section which allows you to tell the printer the type of paper, size desired, orientation of photo to horizon and etc. There is also likely a selectable setup procedure on the printer's own display to do the same... It sounds like a basic setup format issue....

Apr 02, 2010 | HP OfficeJet 6210 All-In-One InkJet...

1 Answer

Printer Model : hp LaserJet 3020 OS : Windows XP(32 bit) Problem : When I did my last firmware update I interrupted by pressing the cancel button on my printer control panel as it showed "Printing...


Never ever touch the printer while upgrading the firmware.
You now need to replace the formatter
  • DO NOT power cycle the printer or the PC during this process or the printer may become unstable and or unusable without further attention from HP . The firmware update can take up to 5 minutes to complete. Please be patient.
  • During the printer firmware update, the liquid crystal display (LCD) on the printer control panel will display "Printing Document" and will change to "Erasing". After a short while, the LCD display will change to "Programming". After a short while, the LCD will display "complete : )" and the "Ready" LED on the printer will be flashing. The printer will automatically power cycle to reboot and will make noises similar to power on.

Jan 28, 2010 | HP LaserJet 3020 All-In-One Printer

1 Answer

When printer is set up to print, it makes a brief knocking sound and on little screen at top it says...unlock scanner


If the printer LCD screen continues to display the same error message, do the following:
Remove both cartridges from the printer.
Move the red lock switch (at the back of the printer) from the down position to the up position, and then move it back to the down position.
Unplug the printer and turn it onto its left side.
Then return the printer to the upright position and reapply the power supply.
Attempt this fix twice and then try to print and scan once more.
note : Installing the wrong upgrade file will not cause damage to the printer, but the LCD display will display some characters incorrectly. Downloading and installing the correct firmware will resolve this issue

Jul 05, 2008 | Lexmark Printers & Copiers

3 Answers

MP780 - LCD Display off


Same problem - for a few days the LCD screen showed garbage intermittently , then machine wouldn't power up and out of warranty. Good machine til then.

Oct 12, 2007 | Canon PIXMA MP780 All-In-One InkJet...

1 Answer

Display


Yor LCD screen may need to be replaced.

Jul 24, 2007 | Brother MFC-5840CN All-In-One InkJet...

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Printers & Copiers Experts

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Rick Johnson
Rick Johnson

Level 2 Expert

84 Answers

John mullen

Level 2 Expert

245 Answers

Are you a Brother Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...