Question about Sevylor Fish Ranger 280

1 Answer

How many peaple can set into boat? - Sevylor Fish Ranger 280

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 463 Answers

This is a single person craft. So ... 1 person.

Posted on Mar 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 03 Sun Tracker pontoon & Merc 60 my throttle trim will lower motor but not raise it.It works fine from motor ,up & down okAlso just had voltage reg. replaced and tach stopped working .Help


Time to just go threw all the wiring. You have a boat. It's on the water or not. On the water electrolysis kicks in 1000%. On land corrosion set in. Check and clean the wire plugs, replace if necessary. Replace ground point connectors. Add wire if necessary. Just a note. When I do boats, I solder all connections and use silicone shrink wrap on the wires.

Jul 01, 2015 | Rowing & Pontoon Boats

1 Answer

HELP! My new little 200 boat will NOT INFLATE! Have tried everything. I had another one that inflated immediately and this one will not! it is as if it has no way in the valves for the air to get into...


Hi, perhaps the problem may lie with the inflating method. Have you checked to see if the pump is actually giving air? These rafts usually have multiple bladders, are they all giving you this problem? Also, there is a plastic flap at the inside the base of the valve to prevent too much air from escaping before you plug it. you mush insert the air chuck adapter past this point. Good Luck!

Nov 10, 2010 | Intex Excursion 4 Inflatable Boat Set

1 Answer

Best way to locate and repair a slow leak in a intex seahawk 500 inflatable


Get some bubble bath, mr. bubble, or just dish soap, thinned out with water, spray it all over the boat, you will get it cleaned up and find the leak at the same time. When you see th e stream of bubbles coming out, mark it, get it dried off and patch it up. I think they use a contac cement on the Hypolon boats, or is it neoprene? Do you have a patch kit? Any pieces of material for a patch? The hardware store has pvc rubber used for shower pans, that might stick on there, clean it good with laq thinner, and brush on some glue, both pieces, let dry, then slap them together. You will know if it will work. Or else look up the manufacturers recommendations. he boat supply might have patch kits in stock. Hope this helps.

Jun 24, 2010 | Intex Excursion 4 Inflatable Boat Set

1 Answer

I need to find out what 1 meter 90 centimeters is in feet an in inches. can you tell me


190 divided by 2.54 = inches. You do the math and convert that to feet and inches.

Jan 28, 2010 | Intex Mariner 4 Boat Set

1 Answer

Is it compatible 3.5 HP engine with the boat? (mariner 4) if yes , when i used %30 of power just alone back side go down and can not control properly . engine is TOHATSU M 3.5 S


Your motor is too large.

For the Intex Mariner 4 Intex recommend an absolute maximum of 3HP (2,2kW) and the motor must not weigh more than 40lb (18,2kg).

Those limits assume that you are using the Intex motor mount kit (Part No. 10658) and that the boat is correctly loaded and inflated.

In reality and from experience I would personally recommend 2HP maximum power and to keep the motor as lightweight as possible. Although the Intex Mariner 4 can take a motor mount, it's really a rowboat and is not suited to using a motor for extended periods, but just as a convenient tender to a larger boat it's fine.

Dec 15, 2009 | Intex Mariner 4 Boat Set

2 Answers

My son's intex has a puncture i have tried the


you must clean the area really well before the glue will stick. first, soap and water the area, then rinse. then, alcohol to wipe clean and dry the water from the area.
then, use cpvc pipe primer (used by plumbers) to clean the area and the inside of the patch.
then, vinyl cement (comes with intex boats) or "seal all" (bought at home depot). apply liberally on both surfaces and hold firmly into place. put a weight ontop if you can to hold the patch. let dry for a few hours. should be good to go.
i've patched my intex mariner about 8 times. patches all hold well.

Sep 29, 2009 | Intex Mariner 4 Boat Set

Not finding what you are looking for?
Sevylor Fish Ranger 280 Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sevylor Rowing & Pontoon Boats Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Bill Eager

Level 3 Expert

421 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Sevylor Rowing and Pontoon Boat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...