Question about HP Compaq ProLiant ML110 G4 Server

2 Answers

Server error i am using HP ML 150 G3 Server,whenever i restart the server i am getting the error 02A2 BMC syste event log (SEL)Full.kindly help and after login the server the error is the following boot start or system start drivers faild to load ohci 1394 Raviraj.Avanty

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 106 Answers

The System Event Log may become full of erroneous IPMI Events reported by the System BIOS. When this occurs, the following message may appear during Power-On Self-Test (POST) and POST cannot continue without user input:
02a2: BMC System Error Log (SEL) Full
Press F1 to Continue, Press F2 to Setup
If the above message appears during POST, perform the following steps to run BIOS setup and delete the System Event Log:

  1. Boot the server and press the F10 key when prompted to run BIOS Setup.
  2. Select the "Advanced" menu.
  3. Scroll down to "IPMI" and press the ENTER key
  4. Scroll down to the System Event Log and press the ENTER key.
  5. At the "Clear System Event Log" selection, press the ENTER key to toggle between "Enable" and "Disable."
  6. Select "Enable."
  7. Press the F10 key to Save the changes and exit the BIOS Setup.

Posted on Aug 16, 2010

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 44 Answers

Enter into bios and Clear BMC log .

Posted on Nov 25, 2011

1 Suggested Answer

  • 101 Answers

SOURCE: server error

Clear System Event Log thru CMOS setup or the management software provided with server . The SEL is full that is the reason the error message

Posted on Mar 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BMC Heartbeat blinking


Then you need to look into your System Event Log (SEL) entries to review the issue that is causing it. If the BMC is showing this heartbeat light, that means that there are critical errors piling up in the BMC's SEL log.

You can either do this through the BIOS (assuming IBM implemented that functionality here) OR you can log into your BMC over your OoB network. (Assuming SSH/telnet is not disabled and has a user configured.)

We can not help with this issue any further without SEL logs.

Jul 09, 2014 | IBM System x3200 M3 7328 Server tower ...

1 Answer

Where is poweredge 1800 display led connector


http://www.dell.com/support/troubleshooting/us/en/19/KCS/KcsArticles/Print?he Embedded System Management (ESM) log - also called System Event Log (SEL) or hardware log - reports potential hardware problems in Dell PowerEdge servers. Sometimes, simply turning off the server and disconnecting it from the electrical outlet will remove the error message. Wait approximately 10 seconds, and then reconnect the power cable and restart the server.

Other times, you will need to clear the ESM log to remove the error message. For instance, error code SEL FULLindicates that you will need to clear the ESM log. (You will lose the server's event history.) There are different ways to clear the ESM log.

To use DSET to Clear the ESM Log
  1. Download and open the DSET utility.
  2. Click the plus (+) next to System, and then click the plus (+) next to Logs.
  3. Click ESM to highlight it.
  4. Click Clear ESM Log located in the upper-right corner of the page.
To use OpenManage Server Administrator (OMSA) to clear the ESM log
  1. Start OpenManage Server Administrator (OMSA).
  2. Log in to OMSA by entering your username and password, and then press Enter.
  3. Click the Logs tab, and then click Hardware.
  4. Click Clear Log located next to Options.
To use Dell IT Assistant to clear the ESM log
  1. Start IT Assistant.
  2. From the middle System Tree bar, select your server by clicking it.
  3. Click the Logs tab, and then click Clear Log in the upper-right corner of the page.
Find your Dell PowerEdge server model in the chart below for other ways to clear the ESM log:

PowerEdge server model How to clear the ESM log 2300, 2400, 2450, 2500, 2500SC, 2550, 4300, 4350, 4400, 6300, 6350, 6400, 6450
Use the Log2Txt.exe utility to clear the ESM log:
  1. Start your server to the Log2Txt utility.
  2. When you see the ESM Log main menu appear, press 2 on your keyboard to select Clear ESM log.
  3. When the ESM Log main menu reappears, press 5on your keyboard to exit the utility.
1650, 1850, 1800, 2600, 2650, 2800, 4600, 6600, 6650, 7150, 6800, 6850, R900
Use the DRAC or ERA to clear the ESM log:
  1. Type the IP address of the Remote Access Controller (RAC) in the web browser address bar, and then press Enter.
  2. Log in to the RAC.
  3. Click the Logs tab, and then click Hardware.
  4. Click Clear Logs located in the upper-right corner of the page.
1850, 2800, 2850, 6800, 6850
Use the program BMCCFG.exe to clear the ESM logs:
  1. Download and extract the Dell OpenManage Deployment Toolkit here.
  2. Go to x:\Dell\Toolkit\Tools, where x is your primary hard disk drive.
  3. Copy the file BMCCFG.exe to a bootable floppy disk.
  4. Start the server from the bootable floppy disk.
  5. At the command prompt, type bmcc - clearsel, and then press Enter.
    The message "Clearing SEL" will display while the log clears.
1950, 2900, 2950, DP500, DP600, NF500, NF600
Use the BMC/BIOS to clear the ESM log:
  1. To open the BMC menu, press the Control + Ekeys during POST.
  2. From the list, select System Event Log, and then press Enter.
  3. Select Clear System Event Log, and then pressEnter.
=8590&doclang=EN

Jun 09, 2014 | Dell PowerEdge 1800 Server

1 Answer

Power is 2950 i912 sel full


Namrata_stha,

The I912 error is referring to the System Event Log is full of events and because of this is unable to log anymore. You must clear the log in order for the Server Management controller to log any more events. Now depending on the OS installed there are different ways to clear it. If Windows Server 2k8 you would use this command - wevtutil el ' foreach { wevtutil cl $_ }
Where with Server 2003 you can go tot he Event viewer and clear it.

Let me know if this helps.

Feb 04, 2014 | Dell PowerEdge Computer Servers

1 Answer

Sel full 1912 error


Hello,

You will get the "Sel Full 1912 error" on your server when the system event log is full and unable to record further events. You must clear the event log before the error will cancel. Boot your system into the BIOS/CMOS, locate the system logs and select clear log, reboot your system. Once the system is back up, I would go into the admin task folder and make sure the logs are clear there as well.

Good Luck.

Please rate my solutions here on FixYa.com

Jan 01, 2012 | Dell PowerEdge 2950 (becwfk1_6) Server

1 Answer

C2A2: system event log (sel) full


even tough you did not specify the generation of your server
if this is the complete error message

02a2: BMC System Error Log (SEL) Full
Press F1 to Continue, Press F2 to Setup
The System Event Log may become full of erroneous IPMI Events reported by the System BIOS
this is the way to resolve it :
If the above message appears during POST, perform the following steps to run BIOS setup and delete the System Event Log:
  1. Boot the server and press the F10 key when prompted to run BIOS Setup.
  2. Select the "Advanced" menu.
  3. Scroll down to "IPMI" and press the ENTER key.
  4. Scroll down to the System Event Log and press the ENTER key.
  5. At the "Clear System Event Log" selection, press the ENTER key to toggle between "Enable" and "Disable."
  6. Select "Enable."
  7. Press the F10 key to Save the changes and exit the BIOS Setup

Aug 18, 2010 | HP ProLiant ML110 Server

1 Answer

Problem rebooting Dell PowerEdge Server 2600


ERROR 02A2: BMC System Error Log (SEL) Full
press F1 to continue or F10 to enter BIOS.
I wait for 2 minutes without doing any thing my server get started normally.
Please help me how to stop this error

Feb 19, 2010 | Dell PowerEdge 2650 Server

1 Answer

ML350 G3 SEEVER IS AUTOMATICALLY SHUTTING DOWN


Check your events log to eliminate software issues. From a hardware point of view the unit could be overheating causing ASR to kick in

May 05, 2009 | HP Compaq ProLiant ML350 G3 Server

1 Answer

Server error


Clear System Event Log thru CMOS setup or the management software provided with server . The SEL is full that is the reason the error message

Mar 02, 2009 | HP ProLiant ML150 G3 Server

1 Answer

02A2: BMC System Event Log(SEL) Full


In HP prolliant server sets, setup also logs system events. This error is due to that log. Enter setup, trace log and clear all events.

Jan 28, 2009 | HP Compaq ProLiant ML110 G4 Server

Not finding what you are looking for?
HP Compaq ProLiant ML110 G4 Server Logo

2,904 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Computer Servers Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a HP Computer Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...