Question about Victor CSR350D Oxygen Regulator

1 Answer

Can't control pressure on victor oxygen regulator

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

One gage is fixed for tank volume the other is variable for you to set for process. if the variable gage dose not work you may have a bad diofram. You could purchase replacement repair parts at your welding supply store.

Posted on Mar 21, 2009

3 Suggested Answers

  • 1 Answer

SOURCE: My victor oxygen regulator stopped regulating.

send it in for repair at any welding supply, most of them will ck' it out for free before they repair it, probably is grain of dirt / sand will cause that effect.

Posted on Jan 23, 2010

  • 5 Answers

SOURCE: Where to find a valve stem or repair parts for my

call ESAB they bought Victor 843-664-4405

Posted on Jul 16, 2009

  • 2468 Answers

SOURCE: need parts for victor 272654 oxy reg

I will sell exterior parts only,I do sell internal regulator parts but only to certified technicians that have the test equip and can re-certify the gauges after a re-build

Posted on Jul 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Victor cga 540 oxy reg. hi side 2000. lo side climbs to max and pop off releases. can adj for short then climbs and releases at pop off


take it to the nearest weld shop, its defective, gages, do one thing, keep pressure where you put it, there is a spring inside and it can get weak by leaving it turned in,
please, take it to a shop, before it fails.

Mar 03, 2011 | Victor CSR350D Oxygen Regulator

1 Answer

Need parts for victor 272654 oxy reg


I will sell exterior parts only,I do sell internal regulator parts but only to certified technicians that have the test equip and can re-certify the gauges after a re-build

Jul 27, 2010 | Victor Welding Equipment

1 Answer

I can't adjust these gauges. How do I do it?


The only part of the gauge that adjust is the tee handle in the middle. the gauge on the left tells you the line pressure to the torch, the gauge on the right tells how much oxygen is in the bottle, usually on a K bottle it is 1800 to 2000 lbs. if you turn the tee handle and the left gauge that tells line pressure does not respond you probably have a bad diaphragm in the gauge. Seek qualified repair man. Thanks

Feb 02, 2010 | Victor CSR350D Oxygen Regulator

1 Answer

My victor oxygen regulator stopped regulating.


send it in for repair at any welding supply, most of them will ck' it out for free before they repair it, probably is grain of dirt / sand will cause that effect.

Jan 09, 2010 | Victor CSR350D Oxygen Regulator

1 Answer

The safetybald is liquing from my oxygen gage what can I do to fix it what part can I buy 


replace it the and check your regulator valve your leaking, may be a seal is out in side your gage. i would replace it fri-st, if that doen't work have your regulator check. good luck

Oct 14, 2009 | Victor CSR350D Oxygen Regulator

1 Answer

My oxygen regulator wont hold proper pressure. It just keeps going up.


Diaphragm needs replacing. Take it to the shop...this needs to be done correctly.

Jul 23, 2009 | Victor CSR350D Oxygen Regulator

Not finding what you are looking for?
Victor CSR350D Oxygen Regulator Logo

Related Topics:

1,679 people viewed this question

Ask a Question

Usually answered in minutes!

Top Victor Welding Equipment Experts

EugenesDIYDen
EugenesDIYDen

Level 3 Expert

479 Answers

John Trevino

Level 3 Expert

1378 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you a Victor Welding Equipment Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...