Question about Kyocera FS-2000D Laser Printer

2 Answers

CLEANING A KYOCERA FS-2000D

Need to know how to clean our kyocera fs-2000d laser printer, it has a spot mark down the middle of the page.

Posted by on

  • Boba Ilik
    Boba Ilik Apr 23, 2009

    Other model printers have the option for cleaning. This model has no such option and there is no discharger (a wire along the drum) visable to be cleaned. In both manuals there is a pure information for any parts and how to do a cleaning.

    That is true that not a genuine printer toner is causing the problem, so the result is not sharp printing at first and later it could be even half a left page dirt, not even clear printed page.



    Who can be of help to tell us how can we do the cleaning. Where is the wire?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Follow the page http://www.fixya.com/support/t1336338-kyocera_fs2000_thin_black_vertical_line

Basically, you remove the cartridge and developer all at once, then remove the waste toner bottle, then push the grey tab in to release the drum cartridge (be very, very careful in removing and putting back in. Any scratches on the drum and you will enjoy black spots permanently on printouts).

On the right side of the grey charger section is a tab you can use to release it. Do this, then put the drum away in a light tight back to prevent damage to it.

The reason why this Kyocera printer doesn't have the primary charger wire cleaner is because it did away with it. It now charges via a black fuzzy looking roller on top which is like the secondary corona charger wire, which then applies it to a roller, which then applies it to the drum. I think this is nice since it should prevent printer quality problems better since there is nowhere for oxidation to really collect. But, OTOH, it does happen anyhow.

I cleaned mine off and the streaks disappeared. I used a non amonia based cleaner to help, since I didn't find any dust on it to begin with. Whatever you choose, do not get your fingers on it, or it will put oil onto the rollers and that will make it worse.

Worked for me.

Posted on May 25, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

Http://safemanuals.com/annexe_Advanced%20Operation_KYOCERA_FS-2000D-_E.htm

here is user guide - read chapter 4 - usually it is bad toner or fuser (maint kit) for all print quality issues in laser printers

Posted on Mar 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printer marks on paper


remove drum /toner unit look at it, it most likely is the problem, is there a line or spots on the shiny surface? clean with soft cloth. otherwise will need to replace. If not that it will be the fuser, back of machine where it gets hot to melt toner to paper.

Mar 26, 2014 | Kyocera FS-2000D Laser Printer

1 Answer

How can i changethe ip adrees from my kyocera fs 2000d


Here's the manual: http://usa.kyoceramita.com/americas/jsp/upload/resource/19873/0/FS2020D-3920DN-4020DNENOG-ADV.pdf

Go to page 65 for Network configurations directions.

Mar 22, 2011 | Kyocera FS-2000D Laser Printer

2 Answers

I have a kyocera FS-2000D with error code: Call for service 0150:0000049. Help...thanks in advance


Error code 0150 is an engine EEPROM communication error. The engine board might need to be replaced. I have heard that sometimes a defective developer unit could cause this same error code. I would try swaping a develper from a working FS-2000D first.

May 20, 2010 | Kyocera FS-2000D Laser Printer

1 Answer

My printer kyocera fs-4000dn print a line of toner as spot


If the spot repeats it self down the page in a repetitive mark the same distance each time you have a build up or scratch on the drum or fuser roller. If the spot is about 2.5-3 inches appart each time it is the fuser roller. If it is more like 5 inches apart each time it is the drum.
If the spot looks more like a wet spot and is about 2 inches apart then you may have a build up on your developer mag roller. let me know if you need more help.

Jan 22, 2010 | Kyocera FS-4000DN Laser Printer

2 Answers

How can i see the serial number or how do i reach it cause i cant


press manu button then go to service then press right errow key goto status page press double enter it will print around 5 or 6 page in second page in down you can find the serial number or else see the back side of the printer it should stikared.............

Nov 05, 2009 | Kyocera FS-2000D Laser Printer

1 Answer

CALL SERVICE 6000:0115785


Error 6000: is a fuser error 0115785 is your page count. You require a replacement fuser

Apr 14, 2009 | Kyocera FS-2000D Laser Printer

1 Answer

I have a kyocera FS-2000D printer. I'm getting an error message: insufficient memory. It will print first page, then stop.


check the basic user guide Chapter 4 - Troubleshooting pages 4-5 to 4-10 about a specific error message.
Make sure you are using the latest print driver from kyocera website !
If is really need it you can expand the memory !!

Dec 30, 2008 | Kyocera FS-2000D Laser Printer

1 Answer

Regardin kyocera FS-2000D


The files called 2000sys.zip & 2000_eng.zip I beleive, if that helps. I bet after you have updated the firmware, you will find the serial number absent from status page, muz get corrupted when the engine firmware chucks the 150 error, Just thought I'd say although is not norm a problem

Oh, It only ever does the 150 once, never if firmware is updated.

Nov 12, 2008 | Kyocera FS-2000D Laser Printer

Not finding what you are looking for?
Kyocera FS-2000D Laser Printer Logo

5,939 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Printers & Copiers Experts

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

NewYork kyocera HP...

Level 3 Expert

513 Answers

pkwc

Level 2 Expert

254 Answers

Are you a Kyocera Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...