Question about Kenmore Washing Machines

1 Answer

My HE 2Plus Has an 01 error code, unplugged washer, waited plugged it in again still unable to clear code

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

F01 - There may be an internal problem with the control, attempt a Hard Reset.

Hard Reset - In some cases the control can be non-functioning or may not accept activation from the control panel. To clear and restart the control follow the these steps:

* Unplug or turn the circuit breaker off for 30 seconds.
* Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
* Press the Pause/Cancel/Stop button twice to clear the "PF" in the display.
* Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.

The F01 generally indicates a failed electronic machine control board.
This error code can sometimes be caused by a glitch or power surge through the electrical lines.
You may be able to clear this code by unplugging the washer for 5 minutes.
If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.

The procedure for accessing and replacing this control board is shown in this image...

http://media.fotki.com/1_p,wkwdftgtbkdgfrwxgtqsskgwtqkq,vi/ksrttqdqrxkssrqtgsd/1/1303472/5961857/image12917img-or.jpg

Be sure to unplug the washer before accessing internal components.
When you access the control board, I recommend transferring the wires from the old control board to the new replacement control board one connection at a time.
Once you have all of the wires transferred, remove the old control board and mount the new control board in the washer.
Reassemble and test the washer.

The "F01" error code indicates a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU.
The "F01" can also be displayed if the onboard "Pump Driver" fails to activate.
Generally in order to correct this failure will require replacing the CCU.
There is no way to test and verify if the control board has failed.
The technical data sheet basically states to replace the CCU.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sears Electric Dryer is flashing F01 What is wrong?


The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.
You can order a new control board from the Sears PartsDirect website.
http://www.searspartsdirect.com/partsdir...
Here's how to do it: http://media.fotki.com/1_p,wkwdftgtbkdgf...


Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Feb 04, 2016 | Sears Kenmore Elite Electric Dryer 69278

1 Answer

What does error code f-01 mean


The "F01" error code is indicating a communication error between the Central Control Unit (CCU) and the EEPROM on board the CCU occurred. Generally in order to correct this failure the CCU board will need to be replaced.
Before you cal the repairman, try unplugging the washer for 3 minutes and then power up again and see if the error clears.

Good luck.

May 11, 2015 | Whirlpool WFC7500VW Washer

1 Answer

Error se 36:01 hp designjet t790


If this error code was caused by a paper jam better could you tell what lead to this erro, unplug the power cable from the printer and clear the blockage. Open and remove the Clean out assembly from the printer and see if you have any particles left inside it. Plug in the power cable again and check if the Error Code has disappeared.

Nov 15, 2013 | Office Equipment & Supplies

2 Answers

How I fix an error code on a LG wm2669hna washer that says TE error


The TE error code indicates a heating error, usually caused by a faulty thermistor. First, attempt to clear the error by unplugging the power cord, waiting for 10 seconds, restore the power, and restart the wash cycle. If the same problem happens again, close water tap, unplug the washer because the unit may require service.

May 17, 2010 | LG WM-2277HW Front Load Washer

1 Answer

Error code print unable 5A on a Brother HL4070CDW


On most printers that are manufactured today have an error chip built onto the motherboard of the printer. If your printer experiences an error. It will register it on on the chip. You will continue getting the error because it needs to be cancelled. To cancel this error follow the instructions below:
1) Turn print on
2) Unplug the printer from the power
3) Wait at least 70 seconds
4) Plug it back in
The error should be cancelled

From Brother's website:
Print Unable ##:
Turn off the printer. Wait a few seconds, then turn it on again. If this does not clear the
problem, call your dealer or a Brother Customer Service.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe Diaz

May 10, 2009 | Office Equipment & Supplies

1 Answer

Error: F 01 and it wont start! I unplugged it for 2 minutes but it still reads 01. I drained the water and it still reads F 01


F01 - There may be an internal problem with the control, attempt a Hard Reset.

Hard Reset - In some cases the control can be non-functioning or may not accept activation from the control panel. To clear and restart the control follow the these steps:

* Unplug or turn the circuit breaker off for 30 seconds.
* Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
* Press the Pause/Cancel/Stop button twice to clear the "PF" in the display.
* Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.

The F01 generally indicates a failed electronic machine control board.
This error code can sometimes be caused by a glitch or power surge through the electrical lines.
You may be able to clear this code by unplugging the washer for 5 minutes.
If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.

The procedure for accessing and replacing this control board is shown in this image...

http://media.fotki.com/1_p,wkwdftgtbkdgfrwxgtqsskgwtqkq,vi/ksrttqdqrxkssrqtgsd/1/1303472/5961857/image12917img-or.jpg

Be sure to unplug the washer before accessing internal components.
When you access the control board, I recommend transferring the wires from the old control board to the new replacement control board one connection at a time.
Once you have all of the wires transferred, remove the old control board and mount the new control board in the washer.
Reassemble and test the washer.

The "F01" error code indicates a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU.
The "F01" can also be displayed if the onboard "Pump Driver" fails to activate.
Generally in order to correct this failure will require replacing the CCU.
There is no way to test and verify if the control board has failed.
The technical data sheet basically states to replace the CCU.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

May 04, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Unable to cancel cycle and restart machine


Instead of hitting cancel twice, only press once,. You should hear the washer unlock. Then try to start again. If that doesn't work, try unplugging the washer in mid cycle. Are you getting and codes popping up?

Feb 22, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

F 2 code on Kenmore Oasis washer?


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Hello our01gt
Welcome to fixya.
I'm Huuum and happy to assist you,

Sounds like we need to try to reset the system!

Huuum At your service!
Lets try this,
Like with an error code.
This can reset the system if it is electronic!
Unplug the washer and wait a 5 minutes then restart it.
If you can't reach the plug, use the breaker to cut the power for 5 minutes.

It's like rebooting your computer when its acting strange!
Usually it corrects some error problems if they are not serious.
Or they are sometimes just a glitch.

Let me know how it works! Waiting for your reply!
Please remember to leave a rating when you are done!
Thank You huuum



This is what Kenmore recommends!!!!!!!!!!



Press STOP once to clear the code.
F=_ "F2" code
Press STOP once to clear code. Press START. If code
appears again, call for service.

Sep 22, 2008 | Kenmore Oasis HE 27082 Top Load Washer

8 Answers

Whirlpool duet washer problem


Our machine was giving the HF code at 37 min after over filling with water. I unplugged the machine, popped the top (took the 3 torx screws off the back) pulled the small hose off the pressure switch sensor (round sensor on the upper back right of the machine) and blew it out just by mouth. It obviously cleared some junk. It works fine now. (also unplugged the 6 wires on the sensor, turned it around and blew on that and heard it clicking, so I knew that was ok.) Hope this helps someone.

Oct 14, 2007 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Ron Lankford

Level 3 Expert

5383 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

reliableservice

Level 2 Expert

313 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...