Question about Poulan Garden

1 Answer

Need fuel/oil mixture ratio for a poulan 3400 chain saw. Much obliged!!!!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Hi, fuel/oil mixture is 40:1 for Poulan. Hope this helps.

Posted on Mar 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Parts catogle for a 017 sthil saw


Try at http://www.jackssmallengines.com/manufacturer/stihl/chainsaw-parts

Jan 10, 2017 | Garden

1 Answer

What is the air gap between ignition coil and fly wheel on a poulan pro pp4218 avx?


For practical application you can just use a new business card or 3x5 recipe card. You don't want to use same card too many times though because thickens of card will change with use, and exposure to liquids. I don't remember right off hand the exact specs but I do know we have used this method for years.

Jan 07, 2017 | Poulan Garden

1 Answer

My s579 bobcat skid steer loader is showing the code M0414(engine oil pressure extremely low) but I checked the oil level and its ok.any idea what could be happening


Connect mechanical oil pressure gauge to check real oil pressure. If OK, replace old pressure sender unit. If actually low, are there leaks? Engine may need bearings replaced, or could be incorrect oil or oil diluted by excessive fuel/leaky injectors.

Jan 29, 2015 | Garden

1 Answer

My troy-bilt snowblower will not start. I stored it right last winter. I filled it with fresh oil & gas two days ago. I've done the starting procedure over and over again. Added fuel stabilizer and seefoam...


Check to see you are getting spark at the spark plug. Take the plug out and put the plug wire on it and ground the the nut on the spark plug to the engine block and crank the engine and see if you get spark at the plug. If so then your carburetor has to be taken apart and cleaned.

Jan 28, 2015 | Garden

1 Answer

Talon electric chainsaw has no power, changed the fuse etc...any ideas??


talon chain saws have two control switches before they will start. One is the trigger that you pull and the other is a button or lever that has to be held in at the same time. These two controls mean that you have to have both hands clear of the chain before it works.

Jan 24, 2015 | Garden

1 Answer

Hi we have a Massey Ferguson Dyna 4 5465 and it was working this morning and then it died we started it up and it ran for about 1/2 a minute when we try starting it now we can hear the fuel pump runs for...


am i to assume its a diesel ,if so sounds like its out of fuel but i could be wrong as its been many years since i have worked on tractors and all the fancy electronic gizmo on modern vehicles can confuse me.Now firstly check the key as no doubt as its a modern one it has a immobilisor and if the head of key loses its chip inside the key head it will never start unlike the old ones that would run on paraffin diesel or petrol ,the later ones were diesel only but again providing they had fuel and oil with the rad topped up they ran 24/7 ,thats a point check the oil level if its low it may stop the engine from starting

Jan 18, 2015 | Garden

1 Answer

I need to know how to set carb to factory settings, already cleaned it. It runs but not right, hard to start


Set flats at neutral to closed just below bowl height. Run mixture screw all way in by hand. Back out 2.5 rounds. Start and observe exhaust. Smells rich turn screw in 1/8 at a time

Jan 08, 2013 | Garden

Not finding what you are looking for?
Garden Logo

Related Topics:

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Poulan Garden Experts

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers

Dwain Pippen

Level 3 Expert

376 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

462 Answers

Are you a Poulan Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...