Question about Hotpoint Aquarius WD63 Front Load Washer/Dryer

1 Answer

Stoped during speen and since then no power. lights are off no conrol lights coming on. cheqed fuses etc, no imrovement. it is hot point AQUARIUS WT 540 16 months old

Posted by on

  • diveatdawn Mar 06, 2009

    half way through a wash it just stopped and tripped the breaker, every time i reset it and try to start the machine the same thing happens

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Hi, it sounds as if your capacitor has blown.
make sure the power has been disconected for at least 24 hours before checking this as it holds power for ages.
where the mains lead goes into the appliance it goes directly to the capacitor, if you know a good sparky he may be able to test it before you get a new one.

Posted on Mar 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My wipers have stoped working on my van. I have cheqed all my fuses and look ok maybe a loos conecion I can not find the motor for washers can you help me thanks


The wiper motor is typically located under the plastic at the base of the windshield, if it isn't already visible. You may have to remove the wiper arms to get the plastic off.
Try replacing the fuses- they are usually real cheap. Or swap with good fuses to test, but never use a higher rated fuse, only what it calls for

Mar 30, 2017 | Cars & Trucks

1 Answer

Troublshoot Mitsubishi wt 46809


Fuse will not be bad if green power light comes on and stays on--if it came on and went off there is a self check.

Likely issues: if no sound also-----problem is in either power supply or set is in shutdown---has a latch circuit.

I have another suggestion based on having worked on hundreds of these sets-----Look first directly under the picture tubes and above the main boards---is there a gray or black plastic tray running under them?

Let me know what you have tried etc by pressing the "make a comment button" here-----

Mar 26, 2012 | Mitsubishi WT-46809 46" Rear Projection...

1 Answer

I have a hot point washin mashine that does not finish a wash and stopes half way through then lights at front of mashine start flashin


Had this with mine. Cleaned the filter (as decribed elsewhere on this site). Also cleaned the component fto which the drain hose attaches - guess this is the pump. Just unclip the drain hose and the hose going into this pump, and check there is nothing obstructing the pump. The clips are a bit of a fiddle, you might want 2 jubilee clips to replace them. Then ran a "maintenance wash" as per manual (ie a hot wash, no clothes, no detergent). Seems OK now

Nov 02, 2010 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Radio stoped working when hot and ground wire made connection to each other


you probably just blowed a fuse.... if the fuse is still good, then you will have to unhook again take a test light and see if you have power.... if so then hook power wire up and see if the power will come on.

Mar 23, 2010 | 2003 Ford Explorer

1 Answer

Door light no working so machine will not start


check power is getting to machine with suitable electrical screw driver.to do this remove top from machine and check live wire just inside rear of machine. fault could be door lock if you have power in machine

Feb 05, 2010 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

My fan blower stoped working , could it be some other than the blower it self?


It could be faulty blower motor brushes or fuse is most likely case
Second option is wiring or conrol switch or relay to and from the blower

Aug 29, 2009 | 1991 Acura Legend

Not finding what you are looking for?
Hotpoint Aquarius WD63 Front Load Washer/Dryer Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

puggy666

Level 1 Expert

47 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...