- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You aren't just looking at the Ghz of the processor.. you have to consider a lot of things. Thank you for putting the make and model of the board. That helps a lot. Looked around for you and I have found that a good processor for that board should be a Intel Pentium 4 2.8ghz 800mhz 478pin 1mbPrescott Cpu . That should be enough to cap off that board. You will ant to look into
is a nice, inexpensive one with copper base and fins. (copper is incredibly thermal conductive.)Above all don't forget to buy some thermal paste. Arctic Silver 5 Thermal Compound - OEMis some good stuff.
Specifications CPU • Supports Intel® P4 Northwood/Prescott/P4 Extreme Edition processors.(PCB v1.1 only) • FSB 400(Northwood only)/533/800MHz • Supports up 3.2GHz and higher speed Memory Speed/CPU FSB Support Matrix Memory Speed/CPU FSB
NO • Intel® 865G Chipset - Supports 800/533/400MHz Intel NetBurst micro-architecture bus. - Integrated graphic controller. - Supports PC2100/PC2700 /PC3200 memory. - Supports AGP 8X/4X at 0.8V (AGP 3.0) or 4X at 1.5V (not support 3.3V) interface. • Intel® ICH5 Chipset - AC'97 2.3 interface - 8 USB 2.0/1.1 ports - 2 channel Ultra ATA/100 Bus Master IDE controller - SMBus 2.0 support - 2 serial ATA Host Controllers - Integrated LAN controller • Support 100(Northwood only)/133/200MHz • Support 400(Northwood only)/533/800MHz Intel NetBurst micro-architecture bus. • Supports two 64-bit wide DDR data channels. • Available bandwidth up to 3.2GB/s(DDR 400) for single-channel mode and 6.4GB/s(DDR 400) for dual-channel mode. • Supports four unbuffered DIMM of 2.5 Volt DDR SDRAM. • Supports up to 4GB memory size without ECC. • One AGP slot supports 8x/4x at 0.8V (AGP 3.0) or 4x at 1.5V (3.3V is not supported). • Three PCI 2.2 32-bit Master PCI Bus slots. - Supports 3.3v/5v PCI bus Interface. • One CNR slot • Dual Ultra DMA 66/100 IDE controllers integrated in ICH5 - Supports PIO, Bus Master operation modes. - Can connect up to four Ultra ATA drives. • Serial ATA/150 controller integrated in ICH5 - Up to 150MB/sec transfer speeds. - Can connect up to two Serial ATA drives. • AC'97 link controller integrated in ICH5 • 6 channels software audio codec C-Media 9739A - Compliance with AC97 v2.2 Spec. - Meet PC2001 audio performance requirement. - Can support SPDIF Out via 3-pin SPDIF bracket only. • Intel 82562EZ - Integrated 10/100 Ethernet MAC and PHY in one chip - Supports 10Mb/s and 100Mb/s auto-negotiation operation - Compliant with PCI v2.2, and LAN on Motherboard (LOM) standard
Probably nothing. If your system works, I would not concern myself greatly with this small detail. The system indicates a 3.4 GHz cpu installed. Your software may misidentify some of the features of your Prescott.
No. DDR replaced the SD in RAM so SDRAM and DDR RAM are two completely different things but each ram type has its own frequency hence you get SDRAM 100(mhz) and SDRAM 133(Mhz) just like you get DDR 1 RAM at 266(mhz) and 400(mhz) and DDR 2 RAM at 533(mhz) and 800(mhz). Therefore as you can see how these things differ, but if your mboard takes SDRAM that it can take and frequency of SDRAM but you must ensure that all the frequencies of all your RAM modules in all your slots correspond otherwise you will have problems, meaning that if you decide to use 133mhz RAM then all your RAM modules that you use must be the same. Let me know how you go. thanks