Question about Crosley CCW5294W Top Load Washer

Open Question

Crosley washing machine won't agitate, spin or pump out

Washing machine won't spin out the water, agitate or spin

Posted by on

5 Suggested Answers

Maanita
  • 1142 Answers

SOURCE: Washing machine won't spin or agitate

It doesn't spin If your washer won't spin, check these:

It doesn't pump or spin
It pumps, but doesn't spin
It spins only with the lid closed
It doesn't pump or spin If it doesn't pump water out or spin, check to see if the motor is running, then proceed as follows:

  • If the motor is running, your washer probably has a frozen pump pulley or a broken pump belt. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it. If the pump belt is broken or looks quite worn, replace it--but be sure to check the pump pulley before you change the belt.


  • If the motor isn't running, the lid switch may be defective. If so, the washing machine can't spin and may not function at all. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washing machine to get to the switch. If it's defective, you need to replace it.


It pumps, but doesn't spin If your washer pumps out the water but doesn't spin, check these:

  • The lid switch may be defective. If it is, the washing machine doesn't spin. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washing machine to get to the switch. If it's defective, you need to replace it.


  • The motor coupler may be broken. Many Whirlpool®-manufactured washers use a small, relatively inexpensive motor coupling. It's plastic and rubber and is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. You may need to replace it.


  • A belt may be broken. Many washing machines have one or two belts. If a belt is broken or badly worn, you need to replace it with a genuine belt from the manufacturer. (Some washing machine belts are designed with special characteristics not found in automotive belts.)


  • The clutch may be worn. If your washer is a GE, it may use a clutch to come up to the proper spin speed. As the clutch wears out, it may prevent the unit from spinning well or at all. If the clutch is worn, you need to replace it. For this job, you probably want to hire a qualified appliance repair technician.


  • The drive motor may be defective. Many washer brands use a reversing motor. For agitation the motor runs in one direction, for spinning and draining, the other. It's possible for a motor to burn out in one direction and continue to operate in the other. If this happens, you need to replace the entire motor.


  • The transmission may not be shifting properly. Older washers produced by Whirlpool® have a transmission with an electro-mechanical shifter. If the shifter becomes even partially defective, the unit may drain the water but not spin. This is a complex system, if your washer has a shifter problem, you may want to hire a qualified appliance repair technician to repair it.


  • The spin bearing or basket drive may be worn or seized. These components allow the inner tub to spin freely inside the outer tub. When this is the problem, you usually hear a loud sound during the spin cycle. Call a qualified appliance repair technician.


It spins only with the lid closed For safety, washing machines are made so that they spin only with the lid closed. The lid switch prevents the spinning action when the lid is up.

Posted on May 29, 2008

Spiz
  • 1 Answer

SOURCE: Our Fisher and Paykel Pride

Sounds like your pump is blocked. **UNPLUG the machine**. lift or drag the machine to a spot where you can let the water dump out. The water comes out fast and makes a big mess. Tilt the machine back. On the front-right underside of the machine you will see the pump with the fan hanging down. Unplug the white plug and the earth cable from the back of the pump. You might notice that there is a white plastic clip that you can move to the side. Hold the clip out and twist the pump clockwise. At this point the pump will drop out and water will go everywhere. Try and take the pump out kinda fast so that the coil does not get too wet while the water is dropping out. you might find a blockage (coil, hair clip, underwire etc) sticking out from where the pump impeller sits. Pull out your blockage and check that the pump spins freely when you spin it by hand. If it does not spin freely you need a new pump.

Now, after you unblock your pump, you can put it back together the same way you took it off. Make sure the white plug is not wet before plugging it into the pump and make sure the pump coil is dry too! use a blowdryer to dry for a minute if unsure. When twisting the pump back in, the wires should be at the back of the machine and the earth cable is kinda close to the rotor (motor). Make sure the pump is sitting flat so the seal works too. That clip should click lock back into place to hold the pump from turning. The washer will not spin until all the water is out in case you are wondering. Hope this helps!

Posted on Aug 02, 2008

kram26
  • 544 Answers

SOURCE: washer will not agitate or spin

HI,

you can view this site to have some ideas about your agitator problem.

http://sites.google.com/site/sublimeappliancerepair/washer-will-not-spin/agitator-woes

any further question let me know.

thanks,

Posted on Mar 29, 2009

  • 10 Answers

SOURCE: Kenmore Washing Machine won't agitate, spin, or drain

It sounds like the motor needs to be replaced, you can drain the water by taking the drain hose from the drain and lowering down water will drain.

Posted on Jun 01, 2009

  • 132 Answers

SOURCE: whirlpool washing machine won`t spin or pump out

1-check the drain hose maybe cloged 2-check the drain filter maybe filed with materials 3- check no spin mode maybe you selected thank you

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Figidaire FTF630as0 won't agitate. The door locks and water drains but won't agitate or spin


Hello Tina Kaha - Often when a unit does not spin, it is because the unit cannot properly drain and dispose of the water and detergent solution. Does the unit make a humming noise? If so, the drainage hose/pump may be clogged and needs to be cleaned. If not, the washer may possibly be experiencing an issue with the door lock assembly, faulty pump, timer or control board not communicating correctly. Because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair the unit.

Apr 19, 2013 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Crosley 5000 front load washer won't spin


Hello - Does the drain pump make a humming noise? If so, you possibly have a restriction in the drain line or siphoning. Try setting the cycle to spin only and verify if water pumps out. If it does not, the unit could possibly be experiencing an issue with either the pump, door lock assembly or timer. Contact a professional to move forward accurately.

Nov 24, 2012 | Crosley Washing Machines

1 Answer

Machine won't spin, therefore water cannont be emptied. The agitator works. I have a top open Kenmore 90 series machine.


Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101

Aug 14, 2011 | Kenmore Washing Machines

1 Answer

WASHER FILLS WITH WATER, THEN WON'T AGITATE. TURN KNOB TO SPIN AND IT DRAINS THEN SPINS. STILL WON'T AGITATE


WASHER FILLS WITH WATER, THEN WON'T AGITATE. TURN KNOB TO SPIN AND IT DRAINS THEN SPINS. STILL WON'T AGITATE please show me a diagram

Jun 14, 2011 | Whirlpool LSR7333 Top Load Washer

1 Answer

Machine won't agitate or spin


Dear customer,


 We recommend u to do the following when the washer doesnt spin or agitate,
  1. Test the lid switch
  2. Inspect the motor coupler
  3. Inspect the drive belt (belt drive only)
  4. Inspect under the washer for soot (clutch)
  5. Test the motor
  6. Inspect the pulley
  7. Test the transmission
  8. Inspect the agitator
  9. Inspect the pump coupling
  10. Test the timer control
  11. Test the centrifugal switch
  12. Test the water level switch
for more details about self testing plz try the link  http://www.acmehowto.com/howto/appliance/washer/washer.php


Plz rate this solution.. thank you.. 

Apr 08, 2009 | Crosley Washing Machines

1 Answer

Crosley caw5923mqd Top Load washer spins but leaves A LOT of water in the clothes


have you checked the pump out of the maachine
the pump may be blocked restricting water flow
if that is ok maybe you need to give the n
machine a hot wash the seals may be draging the spin down

Oct 12, 2007 | Crosley CAWC529JQ Top Load Washer

Not finding what you are looking for?
Crosley CCW5294W Top Load Washer Logo

Related Topics:

650 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crosley Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

sonic boom...
sonic boom...

Level 3 Expert

1557 Answers

Are you a Crosley Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...