Question about Velodyne SPL800R Subwoofer Speaker

1 Answer

Hooking power amp to back of sub

I just purchased a new amp for my spl 8 sub and forgot the order to hook up the wires in back velodyne spl 8

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 124 Answers

Contact Velodyne.

Should have been a sheet in the box with amp for this

Posted on Dec 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On the back of the speaker has two wire hook ups do i bridge from one side of speaker too the other or is it left and right


Get the user's manual for hookup instructions. Don't bridge anything that you are not sure of. If you are referring to the speakers connections, they are used only if you do not have a sub out from the receiver.

Mar 09, 2010 | Velodyne SPL-1000 Subwoofer

1 Answer

Do you repair velodyne fsx 12 subwoofers


what is wrong with it ? is it the sub ? the sub surrounds ? the amp ?

more info please :)

Jan 27, 2010 | Velodyne SPL-1000 Subwoofer

1 Answer

Velodyne sub woofer: Series S Model: VA08BVX10


The volume control pot can be replaced.

Any good quality audio shop or electronics repair shop should be able to fix this.


Nov 17, 2009 | Velodyne SPL-1000 Subwoofer

1 Answer

SPL8R Velodyne sub - Same probelm


Go to the Velodyne web site and check the service center locations.

They may have one in your area.

It sounds like the amp may be the problem. That may be all you need to send.

Best bet, Contact Velodyne.

Jun 08, 2009 | Velodyne HGS-10 Subwoofer

1 Answer

Speaker would push out and stay out with a hum when turned on.


Sounds like the "servo" on this unit has gone bad.

You will need to contact Velodyne for service on this.
It is the only place to get parts and service for this unit.

Apr 01, 2009 | Velodyne SPL-1000 Subwoofer

1 Answer

No volume control on Velodyne SPL12BV sub amp


If my memory serves me on this amp, the volume control is actually a chip in the pre-amp section.

You could try and replace the actual knob on the panel and see if that fixes the problem.
If not, you will most likely have to send the amp section back to Velodyne for repair.

If you do send the amp back, use some masking tape and mark the speaker leads. Hooking these back up wrong will blow the driver and the amp.

Mar 26, 2009 | Velodyne SPL-1000 Subwoofer

1 Answer

When powered on speaker pushes all the way out


The problem is in the Amp. Velodyne is the only place you can get it repaired.

You will need to contact Velodyne for service

Mar 20, 2009 | Velodyne SPL-1500R Subwoofer

1 Answer

Velodyne SPL-1000 II subwoofer only snaps, pops and hisses


Go to the Velodyne web site, look under the support section and check the service center listings.

Also you could try the place you purchased the unit.

Dec 30, 2008 | Velodyne SPL-1000 II Subwoofer

1 Answer

No bass...


One of a few things.

The fuse inside the amplifier section is blown.
The amplifier has died
The speaker is dead.

Best to return to the place you purchased the unit or contact Velodyne for service.

Dec 16, 2008 | Velodyne VX-10 Subwoofer

Not finding what you are looking for?
Velodyne SPL800R Subwoofer Speaker Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Velodyne Speakers & Subwoofers Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

 Grubhead
Grubhead

Level 3 Expert

4584 Answers

Carlos Jaen

Level 3 Expert

435 Answers

Are you a Velodyne Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...